Troubleshooting • Re: ca-certificates upgrade error?
According to the Debian ca=certificates developer it is not a bug, and presumably nothing to worry about.Debian Bug report #1032814 ca-certificates.crt does not contain exactly one certificate or...
View ArticleNetworking and servers • Re: Randomised MAC addresses
Hi - thanks for the reply. I had come to the same conclusion but can't locate the MAC address that is clashing on the router.Did think about dusting off my copy of Wireshark but took the easy route...
View ArticleClik here to view.
Troubleshooting • Re: My Raspberry Pi3B+ is very sluggish
What does the pcb say ?Statistics: Posted by gordon77 — Sat Jun 14, 2025 8:16 am
View ArticleOther RP2040 boards • Re: RP2354 sample fails to flash, behaves erroneously
What else do you have there?I removed a single 10k pulldown resistor that was connected along the trace connected to D3 and it seems to have fixed both the bootloop...D3 is also /HOLD4.4 HOLD...
View ArticleInterfacing (DSI, CSI, I2C, etc.) • Re: CM5 and SMI
the RP1 doesnt have a SMI interface, but you might be able to reproduce something similar using PIOhttps://github.com/raspberrypi/utils/bl ... s/ws2812.chttps://www.raspberrypi.com/news/piolib ......
View ArticleRaspberry Pi OS • Re: Removing ssh default password warning
I haven't tested this, but what is the result of editing /etc/pam.d/common-session and commenting out the line that calls pam_chksshpwd.so?Code: root@pi500:~# cat /etc/profile.d/sshpwd.shexport...
View ArticleUbuntu • cant get extra CS lines for SPI to work
Hello all. I'm running Ubuntu 24.04 LTS on a 4B pi.I'm trying to add 3 more CS lines to spi0. I've seen samples and I thought I had it correct but I keep seeing:2025-06-15T01:07:16.675845-04:00...
View ArticleOther • Re: symbols set for Lbre Office Draw
are there any symbol sets for Libre Office Draw? Things like resistors, capacitors, diodes etc.Thanks in advanceRogerhttps://www.google.com/search?q=symbols ... ice%20DrawStatistics: Posted by ame —...
View ArticleDevice Tree • Re: pca9548a does not create sub busses on I2C bus 4
I wanted to add a pca9548a multiplexer to my pi 4. This worked fine when using the default I2C bus. Sadly this bus is now in use because of the Argon One V2 case. ..sorry, don't get that! is there an...
View ArticleClik here to view.
Graphics, sound and multimedia • Re: Midi, I2C, Pi 5 RP1 chip, which gpio lib???
Hi!You can check your encoder with these instructions: https://palmopensource.com/hardware/io- ... rry-pi.phpNo pullup needed, 2 pins connected to the MCP and the center pin to ground.NO, I didn't...
View ArticleTroubleshooting • Problem with installing M.2HAT
Hi, the instructions describes the following: sudo raspi-configUnder Advanced Options > Bootloader Version, choose Latest. Then, exit raspi-config with Finish or the Escape key.Run the following...
View ArticleTroubleshooting • pi 3b not booting
I recently got 6 RPi3B's and 5 of 6 work. But #4 has the red led on and the green one stays off. I tested them with the same psu,sd-card and so on.I checked : pin 2 has 5.18V and pin 1 3.29V (HP...
View ArticleTroubleshooting • Re: Raspberry Pi Imager v1.9.4 Not Creating...
I have used nmtui to get network going on a Pi3B with the newest OS without XStatistics: Posted by warnerk — Sun Jun 15, 2025 8:55 am
View ArticlePython • Re: I have installed pyenv and get "No module named 'RPi'"...
When I check "pyvenv.cfg" I get this:(pyenv) danne@RPi-robot:~/pyenv $ cat pyvenv.cfghome = /usr/bininclude-system-site-packages = falseversion = 3.11.2executable = /usr/bin/python3.11command =...
View ArticleRaspberry Pi Connect • Re: being asked for credentials after clicking...
I suspect it is a stored credential or cookie ageing out somewhere. If I log out of the connect site and log back in again, then I'm no longer asked for credentials when I actually connect.I think the...
View ArticleRaspberry Pi OS • Re: Issue deleting packages on the command line
Code: Package '2vcard' is not installed, so not removedWhat am I missing here?TIA, Adriaan.You appear to be totally missing the fact that '2vcard' isn't installed.you could script around dpkg-query to...
View ArticleGeneral discussion • Rasoberry Pi Imager
I have been using raspberry pi imager without any issues for sometime now. I have startedhaving some issues, when i boot up the wifi is not working, even though i setuop the wifi parameters in the...
View ArticleTroubleshooting • Re: Raspberry 5 died
I've risked to burn a new SD card and this time the raspberry did boot succsesfully, now i'm aiming that maybe the problem was with the Argon one V3 case, but I still can't figure out how and why it...
View ArticleGraphics programming • Re: What do we know about the VideoCoreVII GPU?
Idein updated their Python interface to GPU/QPU for the Videocore7https://github.com/Idein/py-videocore7Handy for matrix math?Statistics: Posted by Gavinmc42 — Mon Jun 16, 2025 7:54 am
View ArticleGeneral discussion • Re: Rasoberry Pi Imager
This might be the Imager 1.9.4 issue https://github.com/raspberrypi/rpi-imager/issues/1067So, we could use 1.8.5 to work around it.(Or nmtui / nmcli on the command line)Statistics: Posted by neilgl —...
View Article