Clik here to view.
Raspberry Pi OS • Re: Firefox-ESR in Bullseye (Debian 11) - March 2025...
You mean 11/Bullseye -> 12/Bookworm?Yes I do. Mixing up that releases sometimes, too confusing ToyStory fetish buzzwords Is that the only question looking at (how much time I put in) my last...
View ArticleClik here to view.
Compute Module • Re: cm5 USB 3.0 Power Fault State No input
Hello,While reviewing the CM5 IO board, I noticed that Pin 100 is connected to the CSI (Camera IO port). However, in earlier discussions, it was mentioned that this pin could also be used for other...
View ArticleMedia centres • Re: Peppy player
I had to go through full installation process but it only took 20mins.Make sure that in configuration screen (configure_radio.sh) you'll go for 1602 LCD with i2c backpack and 0x27 address.Then after...
View ArticleCamera board • Re: Problem with Waveshare Rpi Cam G on Raspberry Pi Zero 2W
Raspberry Pi OS has been using libcamera for the last 3 years. OpenCV's VideoCapture only works with simple V4L2 devices.There are multiple threads covering alternative approaches to link libcamera...
View ArticleCompute Module • Re: TVOUT video shaking on monitor
I am using raspberry cm4 io board with 12v dc adapterI have taken tvout from j2 connector of io boardI have setup raspberry pi on pal mode and i am using pal display only,But while booting splash...
View ArticleGeneral • Re: The Raspberry Pi Pico W is not showing up on computers
Could it be your USB cable or your choice of USB port? I have found the Picos totally reliable when used with USB. Thonny never fails to establish a link, this on Raspberry Pi OS or Mac OS.The onboard...
View ArticleDevice Tree • Assistance with Device Tree Overlay for GPIO-Based I2C and...
Hello Raspberry Pi Community,I am working on integrating a Goodix GT9271 touchscreen controller with my Raspberry Pi using a GPIO-based I2C bus. The I2C bus is connected to GPIO10 (SDA) and GPIO11...
View ArticlePython • Re: How to handle bytearray from NFC Tag Reader
The data I actually want to work with is ...\x02enOmega\...What would be a proper way to get this data value only from the Tag or at least to "convert" the bytearray to a list where I can access this...
View ArticleMicroPython • Re: Pico W Reliability
I'd rather find and fix the problem than apply a band-aid.That seems fair enough, though I'd accept a band-aid solution if it means everything works, so properly analsying and fixing the issue can be...
View ArticleDevice Tree • Re: mmc0: ADMA error: 0x02000000 when booting kernel with...
From what I understand, it is easy to use the DTB already loaded and modified by the firmware - ${fdt_addr} should be already initialised to its address.Statistics: Posted by PhilE — Thu Dec 26, 2024...
View ArticleGeneral discussion • Re: Power supply - alternative needed to plug type
I’ve been using Meanwell brand PSUs for several years with no issues. Good value. You can get USB breakouts for ridiculously low prices on aliexpress; just stick “usb c breakout “in the search bar.And...
View ArticleHATs and other add-ons • Re: Power HAT+s specification
Thank you for your suggestions!Not sure about the second option, though, as it still violates the HAT+ requirement I mentioned above and also against "5.1.1 GPIO Pin Assignments" from the R-Pi4...
View ArticleTroubleshooting • Cannot SSH when HDMI LCD is connected
Hi,I’m having trouble connecting via SSH when I attach an LCD (https://pl.aliexpress.com/item/10050067 ... pt=glo2pol) screen to my Raspberry Pi 5. When I use a different LCD monitor with the same...
View ArticleBeginners • Re: Cannot find RPi in systemd but finds it in ssh
When I do not include venv it fails to find the mariadb module. The mariadb module is imported before the sensor_relay module in the script:Code: import osimport globimport timeimport...
View ArticleClik here to view.
Beginners • bme280 sensor not being picked up
I have this sensor attached to my rpi model b: Here's how I currently have it wired up:pin 1 - VCC5 - SCL17 - CS21- ADDR6 - GND20 - SDA `sudo i2cdetect -y 1` does not show anything. I am getting a...
View ArticleGeneral • Re: Run Pin reset timing
From the pico datasheethttps://datasheets.raspberrypi.com/pico ... asheet.pdf"RUN is the RP2040 enable pin, and has an internal (on-chip) pull-up resistor to 3.3V of about ~50kΩ. To reset RP2040,short...
View ArticleGeneral • Setting X or Y PIO registers when FIFO is joined
Hi,In a program I am writing, I want to join RX FIFO and TX FIFO for use by ISR only, since this is mostly an Input application.Now I want to set Y register with number of iterations to repeat....
View ArticleGeneral discussion • Re: .uf2 upload problem (raspberry pi pico 2)
I tested different options - micropyhon or C++ by uploading via Arduino IDEStatistics: Posted by DominikPL — Fri Dec 27, 2024 6:08 pm
View ArticleNetworking and servers • Re: Building a Raspberry Pi 5 Server with 10 HDDs...
Earlier this year i also build this with a pi 5 and 6 HDD's - its getting closer to making a profit each month, and that is the one with a public dashboard.https://youtu.be/zD5zkPcbtawI'm confused....
View ArticleClik here to view.
Camera board • rpicam-lapse - Rpicam timelapse video recording application
Ever wanted to generate timelapse video, without generating hundreds or even thousands of images and requiring FFMPEG to stitch these images into video, all running on Raspberry Pi? Well, fret not, as...
View Article