Apologies for the slow response; I was busy this last week. The (lengthy) output from raspinfo is below. I had to delete some lines to get within the 60000 character limit, so I chose some in the middle of dmesg log that seemed not particularly informative. Hopefully those were not the ones you were looking for.
initial_turbo=60
isp_freq=910
isp_freq_min=500
mask_gpu_interrupt1=16418
max_framebuffers=2
over_voltage_avs=0x19000
pause_burst_frames=1
pciex4_reset=1
pmic_turbo_threshold=1500
power_force_3v3_pwm=1
program_serial_random=1
total_mem=8192
usb_max_current_enable=1
v3d_freq=960
v3d_freq_min=500
vpred=8624
vpred_max=8624
hdmi_force_cec_address:0=65535
hdmi_force_cec_address:1=65535
device_tree=-
overlay_prefix=overlays/
hdmi_cvt:0=
hdmi_cvt:1=
hdmi_edid_filename:0=
hdmi_edid_filename:1=
hdmi_timings:0=
hdmi_timings:1=
cmdline.txt
-----------
reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe cgroup_disable=memory numa_policy=interleave nvme.max_host_mem_size_mb=0 numa=fake=8 system_heap.max_order=0 smsc95xx.macaddr=2C:CF:67:DF:54:42 vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000 console=ttyAMA10,115200 console=tty1 root=PARTUUID=82c49bc4-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=US
pin configuration
-----------------
0: ip pu | hi // ID_SDA/GPIO0 = input
1: ip pu | hi // ID_SCL/GPIO1 = input
2: no pu | -- // GPIO2 = none
3: no pu | -- // GPIO3 = none
4: no pu | -- // GPIO4 = none
5: no pu | -- // GPIO5 = none
6: no pu | -- // GPIO6 = none
7: no pu | -- // GPIO7 = none
8: no pu | -- // GPIO8 = none
9: no pd | -- // GPIO9 = none
10: no pd | -- // GPIO10 = none
11: no pd | -- // GPIO11 = none
12: no pd | -- // GPIO12 = none
13: no pd | -- // GPIO13 = none
14: no pd | -- // GPIO14 = none
15: no pd | -- // GPIO15 = none
16: no pd | -- // GPIO16 = none
17: no pd | -- // GPIO17 = none
18: no pd | -- // GPIO18 = none
19: no pd | -- // GPIO19 = none
20: no pd | -- // GPIO20 = none
21: no pd | -- // GPIO21 = none
22: no pd | -- // GPIO22 = none
23: no pd | -- // GPIO23 = none
24: no pd | -- // GPIO24 = none
25: no pd | -- // GPIO25 = none
26: no pd | -- // GPIO26 = none
27: no pd | -- // GPIO27 = none
28: no pd | lo // PCIE_RP1_WAKE/GPIO28 = none
29: no pu | lo // FAN_TACH/GPIO29 = none
30: no pu | -- // HOST_SDA/GPIO30 = none
31: no pu | -- // HOST_SCL/GPIO31 = none
32: op dh pd | hi // ETH_RST_N/GPIO32 = output
33: no pd | lo // GPIO33 = none
34: op dl pd | lo // CD0_IO0_MICCLK/GPIO34 = output
35: no pd | lo // CD0_IO0_MICDAT0/GPIO35 = none
36: no pd | lo // RP1_PCIE_CLKREQ_N/GPIO36 = none
37: no pd | lo // GPIO37 = none
38: ip pd | hi // CD0_SDA/GPIO38 = input
39: ip pd | hi // CD0_SCL/GPIO39 = input
40: a2 pu | hi // CD1_SDA/GPIO40 = SDA4
41: a2 pu | hi // CD1_SCL/GPIO41 = SCL4
42: a2 pd | hi // USB_VBUS_EN/GPIO42 = VBUS_EN1
43: a2 pu | hi // USB_OC_N/GPIO43 = VBUS_OC1
44: op dh pd | hi // RP1_STAT_LED/GPIO44 = output
45: a0 pd | lo // FAN_PWM/GPIO45 = PWM1_CHAN3
46: op dh pd | hi // CD1_IO0_MICCLK/GPIO46 = output
47: no pd | lo // 2712_WAKE/GPIO47 = none
48: no pd | lo // CD1_IO1_MICDAT1/GPIO48 = none
49: op dh pd | hi // EN_MAX_USB_CUR/GPIO49 = output
50: no pd | -- // GPIO50 = none
51: no pd | -- // GPIO51 = none
52: no pu | -- // GPIO52 = none
53: no pu | hi // GPIO53 = none
101: op dh pu | hi // 2712_BOOT_CS_N/GPIO1 = output
102: a7 pn | hi // 2712_BOOT_MISO/GPIO2 = VC_SPI0_MISO
103: a6 pn | hi // 2712_BOOT_MOSI/GPIO3 = VC_SPI0_MOSI
104: a6 pn | lo // 2712_BOOT_SCLK/GPIO4 = VC_SPI0_SCLK
110: ip pd | lo // GPIO10 = input
111: ip pd | lo // GPIO11 = input
112: ip pd | lo // GPIO12 = input
113: ip pd | lo // GPIO13 = input
114: a1 pd | lo // PCIE_SDA/GPIO14 = SPI_S_MOSI_OR_BSC_S_SDA
115: a1 pd | lo // PCIE_SCL/GPIO15 = SPI_S_SCK_OR_BSC_S_SCL
118: ip pd | lo // GPIO18 = input
119: ip pd | lo // GPIO19 = input
120: ip pu | hi // PWR_GPIO/GPIO20 = input
121: ip pd | lo // 2712_G21_FS/GPIO21 = input
122: ip pu | hi // GPIO22 = input
123: ip pd | lo // GPIO23 = input
124: a4 pn | lo // BT_RTS/GPIO24 = UART_RTS_0
125: a4 pu | lo // BT_CTS/GPIO25 = UART_CTS_0
126: a4 pn | hi // BT_TXD/GPIO26 = UART_TXD_0
127: a4 pu | hi // BT_RXD/GPIO27 = UART_RXD_0
128: op dh pd | hi // WL_ON/GPIO28 = output
129: op dh pd | hi // BT_ON/GPIO29 = output
130: a1 pn | hi // WIFI_SDIO_CLK/GPIO30 = SD2_CLK
131: a1 pu | hi // WIFI_SDIO_CMD/GPIO31 = SD2_CMD
132: a1 pu | hi // WIFI_SDIO_D0/GPIO32 = SD2_DAT0
133: a1 pu | hi // WIFI_SDIO_D1/GPIO33 = SD2_DAT1
134: a1 pu | hi // WIFI_SDIO_D2/GPIO34 = SD2_DAT2
135: a1 pu | hi // WIFI_SDIO_D3/GPIO35 = SD2_DAT3
200: ip pd | hi // RP1_SDA/AON_GPIO0 = input
201: ip pd | hi // RP1_SCL/AON_GPIO1 = input
202: op dh pd | hi // RP1_RUN/AON_GPIO2 = output
203: op dh pd | hi // SD_IOVDD_SEL/AON_GPIO3 = output
204: op dh pd | hi // SD_PWR_ON/AON_GPIO4 = output
205: a4 pu | lo // SD_CDET_N/AON_GPIO5 = SD_CARD_PRES_G
206: ip pd | hi // SD_FLG_N/AON_GPIO6 = input
208: ip pd | lo // 2712_WAKE/AON_GPIO8 = input
209: op dh pd | hi // 2712_STAT_LED/AON_GPIO9 = output
212: ip pd | lo // PMIC_INT/AON_GPIO12 = input
213: a2 pu | hi // UART_TX_FS/AON_GPIO13 = VC_TXD0
214: a3 pu | hi // UART_RX_FS/AON_GPIO14 = VC_RXD0
232: a1 -- | hi // HDMI0_SCL/AON_SGPIO0 = HDMI_TX0_BSC_SCL
233: a1 -- | hi // HDMI0_SDA/AON_SGPIO1 = HDMI_TX0_BSC_SDA
234: a1 -- | hi // HDMI1_SCL/AON_SGPIO2 = HDMI_TX1_BSC_SCL
235: a1 -- | hi // HDMI1_SDA/AON_SGPIO3 = HDMI_TX1_BSC_SDA
236: a2 -- | hi // PMIC_SCL/AON_SGPIO4 = BSC_M2_SCL
237: a2 -- | hi // PMIC_SDA/AON_SGPIO5 = BSC_M2_SDA
vcdbg log messages
------------------
004938.840: *** Restart logging
004953.155: Initial voltage 800000 temp 23541
005153.604: avs_2712: AVS pred 8624 862400 temp 22991
005157.206: vpred 862 mV +0
005965.333: FB framebuffer_swap 1
005984.711: Select resolution HDMI0/2 hotplug 1 max_mode 2
006001.138: HDMI0 edid block 0 offset 0
006003.522: 00ffffffffffff0010acc2d054554b31
006009.194: 281c010380351e78eaad75a9544d9d26
006014.866: 0f5054a54b008100b300d100714fa940
006020.539: 8180d1c00101565e00a0a0a029503020
006026.212: 35000e282100001a000000ff0032394a
006031.885: 3050384135314b55540a000000fc0044
006037.558: 454c4c205032343138440a20000000fd
006043.231: 0031561d711c000a202020202020012b
006061.285: HDMI0 edid block 1 offset 128
006063.841: 02031bb1509005040302071601061112
006069.513: 1513141f2065030c001000023a801871
006075.186: 382d40582c45000e282100001e011d80
006080.859: 18711c1620582c25000e282100009ebf
006086.532: 1600a08038134030203a000e28210000
006092.205: 1a7e3900a080381f4030203a000e2821
006097.877: 00001a00000000000000000000000000
006103.550: 000000000000000000000000000000d8
006109.242: HDMI0: best-mode 2 (limit 2) 1920x1080 60 Hz CEA modes fe007f80010000000000000000000000 extensions 1
006120.835: Select resolution HDMI1/2 hotplug 0 max_mode 2
006127.757: FB0 disp 0 max-fb 2 1920x1080 stride 3840 base 0x3f800000
006787.175: initramfs (initramfs_2712) loaded to 0x2e350000 (size 0xcaf765)
006802.158: dtb_file 'bcm2712-rpi-5-b.dtb'
006885.989: Loaded overlay 'bcm2712d0'
006959.748: Found camera 'imx708' on port 1, unicam_port 1
007033.423: Loaded overlay 'imx708'
007151.995: dtparam: audio=on
007160.580: Unknown dtparam 'audio' - ignored
007231.324: Loaded overlay 'vc4-kms-v3d-pi5'
007404.676: Read command line from file 'cmdline.txt':
007411.177: 'console=serial0,115200 console=tty1 root=PARTUUID=82c49bc4-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=US'
007633.488: RPM 5914, max RPM 5914
009518.889: Device tree loaded to 0x2e33c200 (size 0x13d30)
009592.365: Starting OS 9592 ms
009597.890: 00000040: -> 00000480
009599.739: 00000030: -> 00100080
009604.452: 00000034: -> 00100080
009609.165: 00000038: -> 00100080
009613.877: 0000003c: -> 00100080
009723.453: sdram: sdram refresh 2081->8324 (1)
069682.262: initial_turbo of 60 deactivated
240554.507: sdram: sdram refresh 2081->4162 (2)
dmesg log
---------
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1]
[ 0.000000] Linux version 6.12.34+rpt-rpi-2712 (serge@raspberrypi.com) (aarch64-linux-gnu-gcc-12 (Debian 12.2.0-14+deb12u1) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Debian 1:6.12.34-1+rpt1~bookworm (2025-06-26)
[ 0.000000] KASLR enabled
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Raspberry Pi 5 Model B Rev 1.1
[ 0.000000] efi: UEFI not found.
** some deleted lines here to get within the character limit **
[ 0.003155] rcu: Hierarchical SRCU implementation.
[ 0.003161] rcu: Max phase no-delay instances is 1000.
[ 0.003201] Timer migration: 1 hierarchy levels; 8 children per group; 0 crossnode level
[ 0.003554] EFI services will not be available.
[ 0.003622] smp: Bringing up secondary CPUs ...
[ 0.003804] Detected PIPT I-cache on CPU1
[ 0.003842] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1]
[ 0.004079] Detected PIPT I-cache on CPU2
[ 0.004105] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1]
[ 0.004297] Detected PIPT I-cache on CPU3
[ 0.004316] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1]
[ 0.004346] smp: Brought up 8 nodes, 4 CPUs
[ 0.004352] SMP: Total of 4 processors activated.
[ 0.004354] CPU: All CPU(s) started at EL2
[ 0.004356] CPU features: detected: 32-bit EL0 Support
[ 0.004358] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.004359] CPU features: detected: Common not Private translations
[ 0.004360] CPU features: detected: CRC32 instructions
[ 0.004363] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.004365] CPU features: detected: LSE atomic instructions
[ 0.004366] CPU features: detected: Privileged Access Never
[ 0.004367] CPU features: detected: RAS Extension Support
[ 0.004368] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.004393] alternatives: applying system-wide alternatives
[ 0.005794] CPU features: detected: Hardware dirty bit management on CPU0-3
[ 0.005968] Memory: 8141888K/8380416K available (14208K kernel code, 2418K rwdata, 4928K rodata, 5696K init, 647K bss, 146464K reserved, 65536K cma-reserved)
[ 0.006139] devtmpfs: initialized
[ 0.008044] Enabled cp15_barrier support
[ 0.008049] Enabled setend support
[ 0.008087] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.008092] futex hash table entries: 1024 (order: 2, 65536 bytes, vmalloc)
[ 0.008206] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
[ 0.008207] 0 pages in range for non-PLT usage
[ 0.008208] 129308 pages in range for PLT usage
[ 0.008288] pinctrl core: initialized pinctrl subsystem
[ 0.008411] DMI not present or invalid.
[ 0.012475] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.012806] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.012834] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.012863] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.012876] audit: initializing netlink subsys (disabled)
[ 0.012932] audit: type=2000 audit(0.012:1): state=initialized audit_enabled=0 res=1
[ 0.013025] thermal_sys: Registered thermal governor 'step_wise'
[ 0.013034] cpuidle: using governor menu
[ 0.013089] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.013108] ASID allocator initialised with 32768 entries
[ 0.013358] Serial: AMBA PL011 UART driver
[ 0.014092] /soc@107c000000/interrupt-controller@7fff9000: Fixed dependency cycle(s) with /soc@107c000000/interrupt-controller@7fff9000
[ 0.014247] bcm2835-mbox 107c013880.mailbox: mailbox enabled
[ 0.014364] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 16, base_baud = 0) is a PL011 rev3
[ 0.014373] printk: legacy console [ttyAMA10] enabled
[ 0.020010] raspberrypi-firmware soc@107c000000:firmware: Attached to firmware from 2025-05-08T14:13:17, variant start_cd
[ 0.024010] raspberrypi-firmware soc@107c000000:firmware: Firmware hash is 6947117700000000000000000000000000000000
[ 0.028979] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.029005] /axi/pcie@1000120000/rp1/csi@128000: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 0.029118] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.029145] /axi/pcie@1000120000/rp1/csi@128000: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 0.032625] bcm2835-dma 1000010000.dma: DMA legacy API manager, dmachans=0x1
[ 0.032874] iommu: Default domain type: Translated
[ 0.032876] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.033188] SCSI subsystem initialized
[ 0.033218] usbcore: registered new interface driver usbfs
[ 0.033224] usbcore: registered new interface driver hub
[ 0.033229] usbcore: registered new device driver usb
[ 0.033294] pps_core: LinuxPPS API ver. 1 registered
[ 0.033295] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.033298] PTP clock support registered
[ 0.033545] vgaarb: loaded
[ 0.033630] clocksource: Switched to clocksource arch_sys_counter
[ 0.239502] VFS: Disk quotas dquot_6.6.0
[ 0.239508] VFS: Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
[ 0.240674] NET: Registered PF_INET protocol family
[ 0.240812] IP idents hash table entries: 131072 (order: 6, 1048576 bytes, vmalloc)
[ 0.242375] tcp_listen_portaddr_hash hash table entries: 4096 (order: 2, 65536 bytes, vmalloc)
[ 0.242401] Table-perturb hash table entries: 65536 (order: 4, 262144 bytes, vmalloc)
[ 0.242408] TCP established hash table entries: 65536 (order: 5, 524288 bytes, vmalloc)
[ 0.242607] TCP bind hash table entries: 65536 (order: 7, 2097152 bytes, vmalloc)
[ 0.243263] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.243363] MPTCP token hash table entries: 8192 (order: 3, 196608 bytes, vmalloc)
[ 0.243399] UDP hash table entries: 4096 (order: 3, 131072 bytes, vmalloc)
[ 0.243463] UDP-Lite hash table entries: 4096 (order: 3, 131072 bytes, vmalloc)
[ 0.243559] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.243719] RPC: Registered named UNIX socket transport module.
[ 0.243721] RPC: Registered udp transport module.
[ 0.243722] RPC: Registered tcp transport module.
[ 0.243723] RPC: Registered tcp-with-tls transport module.
[ 0.243725] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.243729] PCI: CLS 0 bytes, default 64
[ 0.243831] Trying to unpack rootfs image as initramfs...
[ 0.246706] kvm [1]: nv: 554 coarse grained trap handlers
[ 0.246800] kvm [1]: IPA Size Limit: 40 bits
[ 0.246816] kvm [1]: GICV region size/alignment is unsafe, using trapping (reduced performance)
[ 0.246876] kvm [1]: vgic interrupt IRQ9
[ 0.246888] kvm [1]: VHE mode initialized successfully
[ 0.247376] Initialise system trusted keyrings
[ 0.249796] workingset: timestamp_bits=42 max_order=19 bucket_order=0
[ 0.250106] NFS: Registering the id_resolver key type
[ 0.250113] Key type id_resolver registered
[ 0.250114] Key type id_legacy registered
[ 0.250123] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.250126] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.250299] Key type asymmetric registered
[ 0.250301] Asymmetric key parser 'x509' registered
[ 0.250320] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.250351] io scheduler mq-deadline registered
[ 0.250354] io scheduler kyber registered
[ 0.250373] io scheduler bfq registered
[ 0.250704] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/interrupt-controller@7d510600, parent irq: 27)
[ 0.250736] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/interrupt-controller@7c502000, parent irq: 28)
[ 0.250764] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508380, parent irq: 29)
[ 0.250800] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508400, parent irq: 30)
[ 0.250827] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d503000, parent irq: 31)
[ 0.251737] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.347544] Freeing initrd memory: 12976K
[ 0.348362] simple-framebuffer 3f800000.framebuffer: framebuffer at 0x3f800000, 0x3f4800 bytes
[ 0.348371] simple-framebuffer 3f800000.framebuffer: format=r5g6b5, mode=1920x1080x16, linelength=3840
[ 0.348606] Console: switching to colour frame buffer device 240x67
[ 0.350036] simple-framebuffer 3f800000.framebuffer: fb0: simplefb registered!
[ 0.379658] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 0.379949] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 33, base_baud = 6000000) is a Broadcom BCM7271 UART
[ 0.379988] serial serial0: tty port ttyS0 registered
[ 0.380252] iproc-rng200 107d208000.rng: hwrng registered
[ 0.380282] vc-mem: phys_addr:0x00000000 mem_base=0x3fc00000 mem_size:0x40000000(1024 MiB)
[ 0.380460] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe
[ 0.381737] brd: module loaded
[ 0.382560] loop: module loaded
[ 0.382652] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 0.382750] Loading iSCSI transport class v2.0-870.
[ 0.383427] usbcore: registered new interface driver lan78xx
[ 0.383434] usbcore: registered new interface driver smsc95xx
[ 0.383479] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.383493] dwc_otg: FIQ enabled
[ 0.383495] dwc_otg: NAK holdoff enabled
[ 0.383496] dwc_otg: FIQ split-transaction FSM enabled
[ 0.383498] Module dwc_common_port init
[ 0.383692] usbcore: registered new interface driver uas
[ 0.383700] usbcore: registered new interface driver usb-storage
[ 0.383766] mousedev: PS/2 mouse device common for all mice
[ 0.391296] rpi-rtc soc@107c000000:rpi_rtc: registered as rtc0
[ 0.392678] rpi-rtc soc@107c000000:rpi_rtc: setting system clock to 1970-01-01T00:00:10 UTC (10)
[ 0.392962] bcm2835-wdt bcm2835-wdt: Poweroff handler already present!
[ 0.392964] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.394957] sdhci: Secure Digital Host Controller Interface driver
[ 0.394959] sdhci: Copyright(c) Pierre Ossman
[ 0.394987] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.395050] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 0.395059] hid: raw HID events driver (C) Jiri Kosina
[ 0.395075] usbcore: registered new interface driver usbhid
[ 0.395077] usbhid: USB HID core driver
[ 0.395351] hw perfevents: enabled with armv8_cortex_a76 PMU driver, 7 (0,8000003f) counters available
[ 0.395556] NET: Registered PF_PACKET protocol family
[ 0.395576] Key type dns_resolver registered
[ 0.398967] registered taskstats version 1
[ 0.399028] Loading compiled-in X.509 certificates
[ 0.400431] Demotion targets for Node 0: null
[ 0.400434] Demotion targets for Node 1: null
[ 0.400435] Demotion targets for Node 2: null
[ 0.400436] Demotion targets for Node 3: null
[ 0.400437] Demotion targets for Node 4: null
[ 0.400438] Demotion targets for Node 5: null
[ 0.400439] Demotion targets for Node 6: null
[ 0.400440] Demotion targets for Node 7: null
[ 0.400594] Key type .fscrypt registered
[ 0.400596] Key type fscrypt-provisioning registered
[ 0.401433] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@1000120000 ranges:
[ 0.401437] brcm-pcie 1000120000.pcie: No bus range found for /axi/pcie@1000120000, using [bus 00-ff]
[ 0.401445] brcm-pcie 1000120000.pcie: MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000
[ 0.401449] brcm-pcie 1000120000.pcie: MEM 0x1c00000000..0x1effffffff -> 0x0400000000
[ 0.401454] brcm-pcie 1000120000.pcie: IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000
[ 0.401459] brcm-pcie 1000120000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[ 0.401462] brcm-pcie 1000120000.pcie: IB MEM 0x1000130000..0x1000130fff -> 0xfffffff000
[ 0.402774] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0002:00
[ 0.402778] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 0.402780] pci_bus 0002:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb])
[ 0.402783] pci_bus 0002:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff])
[ 0.402794] pci 0002:00:00.0: [14e4:2712] type 01 class 0x060400 PCIe Root Port
[ 0.402799] pci 0002:00:00.0: PCI bridge to [bus 00]
[ 0.402802] pci 0002:00:00.0: bridge window [mem 0x1f80000000-0x1fbfffffff]
[ 0.402818] pci 0002:00:00.0: PME# supported from D0 D3hot
[ 0.403429] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.505633] brcm-pcie 1000120000.pcie: clkreq-mode set to default
[ 0.505636] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC)
[ 0.505656] pci 0002:01:00.0: [1de4:0001] type 00 class 0x020000 PCIe Endpoint
[ 0.505669] pci 0002:01:00.0: BAR 0 [mem 0xffffc000-0xffffffff]
[ 0.505675] pci 0002:01:00.0: BAR 1 [mem 0xffc00000-0xffffffff]
[ 0.505681] pci 0002:01:00.0: BAR 2 [mem 0xffff0000-0xffffffff]
[ 0.505743] pci 0002:01:00.0: supports D1
[ 0.505744] pci 0002:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.513639] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.513647] pci 0002:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]: assigned
[ 0.513650] pci 0002:01:00.0: BAR 1 [mem 0x1f00000000-0x1f003fffff]: assigned
[ 0.513654] pci 0002:01:00.0: BAR 2 [mem 0x1f00400000-0x1f0040ffff]: assigned
[ 0.513657] pci 0002:01:00.0: BAR 0 [mem 0x1f00410000-0x1f00413fff]: assigned
[ 0.513662] pci 0002:00:00.0: PCI bridge to [bus 01]
[ 0.513664] pci 0002:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]
[ 0.513666] pci_bus 0002:00: resource 4 [mem 0x1f00000000-0x1ffffffffb]
[ 0.513669] pci_bus 0002:00: resource 5 [mem 0x1c00000000-0x1effffffff pref]
[ 0.513671] pci_bus 0002:01: resource 1 [mem 0x1f00000000-0x1f005fffff]
[ 0.513674] pci 0002:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512
[ 0.513681] pci 0002:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512
[ 0.513739] pcieport 0002:00:00.0: enabling device (0000 -> 0002)
[ 0.513764] pcieport 0002:00:00.0: PME: Signaling with IRQ 38
[ 0.513804] pcieport 0002:00:00.0: AER: enabled with IRQ 38
[ 0.513859] rp1 0002:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200
[ 0.513862] rp1 0002:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200
[ 0.513873] rp1 0002:01:00.0: enabling device (0000 -> 0002)
[ 0.514463] rp1 0002:01:00.0: chip_id 0x20001927
[ 0.518069] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.518467] genirq: irq_chip rp1_irq_chip did not update eff. affinity mask of irq 100
[ 0.533127] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 106 (m.m.m.m)
[ 0.533189] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.533207] /axi/pcie@1000120000/rp1/csi@128000: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 0.533992] dw_axi_dmac_platform 1f00188000.dma: DesignWare AXI DMA Controller, 8 channels
[ 0.534212] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.534217] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
[ 0.534652] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810
[ 0.534660] xhci-hcd xhci-hcd.0: irq 131, io mem 0x1f00200000
[ 0.534715] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.534717] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
[ 0.534719] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed
[ 0.534758] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 0.534761] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.534763] usb usb1: Product: xHCI Host Controller
[ 0.534765] usb usb1: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.534766] usb usb1: SerialNumber: xhci-hcd.0
[ 0.534863] hub 1-0:1.0: USB hub found
[ 0.534876] hub 1-0:1.0: 2 ports detected
[ 0.534969] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 0.534971] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.534973] usb usb2: Product: xHCI Host Controller
[ 0.534975] usb usb2: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.534976] usb usb2: SerialNumber: xhci-hcd.0
[ 0.535036] hub 2-0:1.0: USB hub found
[ 0.535046] hub 2-0:1.0: 1 port detected
[ 0.535254] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.535258] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3
[ 0.535683] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810
[ 0.535691] xhci-hcd xhci-hcd.1: irq 136, io mem 0x1f00300000
[ 0.535742] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.535744] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4
[ 0.535746] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed
[ 0.535770] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 0.535772] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.535774] usb usb3: Product: xHCI Host Controller
[ 0.535776] usb usb3: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.535777] usb usb3: SerialNumber: xhci-hcd.1
[ 0.535836] hub 3-0:1.0: USB hub found
[ 0.535846] hub 3-0:1.0: 2 ports detected
[ 0.535927] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 0.535930] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.535932] usb usb4: Product: xHCI Host Controller
[ 0.535933] usb usb4: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.535935] usb usb4: SerialNumber: xhci-hcd.1
[ 0.535991] hub 4-0:1.0: USB hub found
[ 0.536001] hub 4-0:1.0: 1 port detected
[ 0.536729] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.537088] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success
[ 0.537499] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.537866] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success
[ 0.538247] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.538591] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success
[ 0.538798] sdhci-brcmstb 1000fff000.mmc: Got CD GPIO
[ 0.538885] mmc0: CQHCI version 5.10
[ 0.539124] mmc1: CQHCI version 5.10
[ 0.540064] of_cfs_init
[ 0.540097] of_cfs_init: OK
[ 0.540250] clk: Disabling unused clocks
[ 0.548945] PM: genpd: Disabling unused power domains
[ 0.577003] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit
[ 0.679901] mmc0: Command Queue Engine enabled, 31 tags
[ 0.679905] mmc0: new ultra high speed SDR104 SDHC card at address 59b4
[ 0.680053] mmcblk0: mmc0:59b4 USD00 29.5 GiB
[ 0.680825] mmcblk0: p1 p2
[ 0.680882] mmcblk0: mmc0:59b4 USD00 29.5 GiB (quirks 0x40000000)
[ 0.724168] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit
[ 0.727026] Freeing unused kernel memory: 5696K
[ 0.727123] Run /init as init process
[ 0.727125] with arguments:
[ 0.727126] /init
[ 0.727127] splash
[ 0.727128] with environment:
[ 0.727129] HOME=/
[ 0.727130] TERM=linux
[ 0.756889] mmc1: new ultra high speed DDR50 SDIO card at address 0001
[ 0.781639] usb 1-1: new low-speed USB device number 2 using xhci-hcd
[ 0.785637] usb 3-2: new low-speed USB device number 2 using xhci-hcd
[ 0.824971] v3d 1002000000.v3d: [drm] Transparent Hugepage support is recommended for optimal performance on this platform!
[ 0.829876] [drm] Initialized v3d 1.0.0 for 1002000000.v3d on minor 0
[ 0.834721] vc4_hvs 107c580000.hvs: bcm2712_iommu_of_xlate: MMU 1000005200.iommu
[ 0.834727] vc4_hvs 107c580000.hvs: bcm2712_iommu_probe_device: MMU 1000005200.iommu
[ 0.834733] vc4_hvs 107c580000.hvs: bcm2712_iommu_device_group: MMU 1000005200.iommu
[ 0.834738] vc4_hvs 107c580000.hvs: Adding to iommu group 1
[ 0.834741] vc4_hvs 107c580000.hvs: bcm2712_iommu_attach_dev: MMU 1000005200.iommu
[ 0.836772] vc4-drm axi:gpu: bcm2712_iommu_of_xlate: MMU 1000005200.iommu
[ 0.836779] vc4-drm axi:gpu: bcm2712_iommu_probe_device: MMU 1000005200.iommu
[ 0.836783] vc4-drm axi:gpu: bcm2712_iommu_device_group: MMU 1000005200.iommu
[ 0.836787] vc4-drm axi:gpu: Adding to iommu group 1
[ 0.836790] vc4-drm axi:gpu: bcm2712_iommu_attach_dev: MMU 1000005200.iommu
[ 0.837411] Console: switching to colour dummy device 80x25
[ 0.843069] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 0.950865] usb 3-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00
[ 0.950873] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 0.950875] usb 3-2: Product: USB Optical Mouse
[ 0.950877] usb 3-2: Manufacturer: Logitech
[ 0.953838] usb 1-1: New USB device found, idVendor=046d, idProduct=c31c, bcdDevice=64.00
[ 0.953841] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 0.953843] usb 1-1: Product: USB Keyboard
[ 0.953844] usb 1-1: Manufacturer: Logitech
[ 0.983826] input: Logitech USB Optical Mouse as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.0/0003:046D:C077.0001/input/input0
[ 0.983896] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.1-2/input0
[ 0.987318] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 1.430840] input: Logitech USB Keyboard as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1:1.0/0003:046D:C31C.0002/input/input1
[ 1.549685] hid-generic 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.0-1/input0
[ 1.552000] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 1.686765] input: Logitech USB Keyboard Consumer Control as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1:1.1/0003:046D:C31C.0003/input/input2
[ 1.741677] input: Logitech USB Keyboard System Control as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1:1.1/0003:046D:C31C.0003/input/input3
[ 1.741718] hid-generic 0003:046D:C31C.0003: input,hidraw2: USB HID v1.10 Device [Logitech USB Keyboard] on usb-xhci-hcd.0-1/input1
[ 1.743965] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 1.861632] usb 1-2: new full-speed USB device number 3 using xhci-hcd
[ 2.021826] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 2.021829] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.021831] usb 1-2: Product: UNO R4 Minima
[ 2.021832] usb 1-2: Manufacturer: Arduino
[ 2.021834] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2.208192] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 2.309863] EXT4-fs (mmcblk0p2): mounted filesystem a36be96c-66be-4487-a7a6-0481bca99d89 ro with ordered data mode. Quota mode: none.
[ 2.533127] systemd[1]: System time before build time, advancing clock.
[ 2.581850] NET: Registered PF_INET6 protocol family
[ 2.582172] Segment Routing with IPv6
[ 2.582180] In-situ OAM (IOAM) with IPv6
[ 2.603478] systemd[1]: systemd 252.38-1~deb12u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[ 2.603489] systemd[1]: Detected architecture arm64.
[ 2.609317] systemd[1]: Hostname set to <raspberrypi>.
[ 2.863329] systemd[1]: Queued start job for default target graphical.target.
[ 2.882046] systemd[1]: Created slice system-getty.slice - Slice /system/getty.
[ 2.882249] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe.
[ 2.882412] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty.
[ 2.882571] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck.
[ 2.882662] systemd[1]: Created slice user.slice - User and Session Slice.
[ 2.882711] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch.
[ 2.882838] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point.
[ 2.882857] systemd[1]: Expecting device dev-disk-by\x2dpartuuid-82c49bc4\x2d01.device - /dev/disk/by-partuuid/82c49bc4-01...
[ 2.882866] systemd[1]: Expecting device dev-dri-card0.device - /dev/dri/card0...
[ 2.882872] systemd[1]: Expecting device dev-dri-renderD128.device - /dev/dri/renderD128...
[ 2.882879] systemd[1]: Expecting device dev-ttyAMA10.device - /dev/ttyAMA10...
[ 2.882901] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes.
[ 2.882926] systemd[1]: Reached target nss-user-lookup.target - User and Group Name Lookups.
[ 2.882948] systemd[1]: Reached target slices.target - Slice Units.
[ 2.882965] systemd[1]: Reached target swap.target - Swaps.
[ 2.882984] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes.
[ 2.883092] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket.
[ 2.883136] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe.
[ 2.883310] systemd[1]: Listening on systemd-journald-audit.socket - Journal Audit Socket.
[ 2.883388] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[ 2.883471] systemd[1]: Listening on systemd-journald.socket - Journal Socket.
[ 2.883832] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket.
[ 2.883902] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[ 2.884003] systemd[1]: dev-hugepages.mount - Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[ 2.884516] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System...
[ 2.885140] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System...
[ 2.885811] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System...
[ 2.885957] systemd[1]: auth-rpcgss-module.service - Kernel Module supporting RPCSEC_GSS was skipped because of an unmet condition check (ConditionPathExists=/etc/krb5.keytab).
[ 2.887343] systemd[1]: Starting fake-hwclock.service - Restore / save the current clock...
[ 2.888188] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout...
[ 2.888990] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes...
[ 2.890237] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs...
[ 2.891346] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod...
[ 2.892869] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm...
[ 2.894254] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore...
[ 2.895315] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse...
[ 2.896472] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop...
[ 2.896630] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root).
[ 2.898306] systemd[1]: Starting systemd-journald.service - Journal Service...
[ 2.905791] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules...
[ 2.906625] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems...
[ 2.907410] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices...
[ 2.908725] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System.
[ 2.909054] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System.
[ 2.909235] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System.
[ 2.910023] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev
[ 2.910242] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes.
[ 2.910659] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 2.910747] systemd[1]: Finished modprobe@configfs.service - Load Kernel Module configfs.
[ 2.910914] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[ 2.910987] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod.
[ 2.911137] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 2.911203] systemd[1]: Finished modprobe@drm.service - Load Kernel Module drm.
[ 2.911357] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[ 2.911427] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore.
[ 2.911575] systemd[1]: modprobe@loop.service: Deactivated successfully.
[ 2.911642] systemd[1]: Finished modprobe@loop.service - Load Kernel Module loop.
[ 2.912624] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System...
[ 2.912734] systemd[1]: systemd-repart.service - Repartition Root Disk was skipped because no trigger condition checks were met.
[ 2.914469] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System.
[ 2.922808] fuse: init (API version 7.41)
[ 2.923405] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[ 2.923508] systemd[1]: Finished modprobe@fuse.service - Load Kernel Module fuse.
[ 2.924233] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System...
[ 2.925980] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System.
[ 2.936190] systemd[1]: Finished fake-hwclock.service - Restore / save the current clock.
[ 2.945897] i2c_dev: i2c /dev entries driver
[ 2.946433] systemd[1]: Started systemd-journald.service - Journal Service.
[ 2.949766] EXT4-fs (mmcblk0p2): re-mounted a36be96c-66be-4487-a7a6-0481bca99d89 r/w.
[ 2.962673] systemd-journald[311]: Received client request to flush runtime journal.
[ 2.976655] systemd-journald[311]: File /var/log/journal/cb792f53419845d3b17675f494f0e038/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 3.550208] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.552607] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040
[ 3.552673] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1
[ 3.552818] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040
[ 3.556193] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2
[ 3.556225] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020
[ 3.562267] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3
[ 3.566267] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020
[ 3.566402] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4
[ 3.567633] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000
[ 3.567714] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0
[ 3.568837] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.572862] rp1-firmware rp1_firmware: RP1 Firmware version eb39cfd516f8c90628aa9d91f52370aade5d0a55
[ 3.576887] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.581413] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.593788] mc: Linux media interface: v0.10
[ 3.593837] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.604795] brcmstb-i2c 107d508200.i2c: @97500hz registered in interrupt mode
[ 3.605607] brcmstb-i2c 107d508280.i2c: @97500hz registered in interrupt mode
[ 3.607182] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.609155] rp1-pio 1f00178000.pio: Created instance as pio0
[ 3.609173] Registered IR keymap rc-cec
[ 3.609200] rc rc0: vc4-hdmi-0 as /devices/platform/soc@107c000000/107c701400.hdmi/rc/rc0
[ 3.611015] input: pwr_button as /devices/platform/pwr_button/input/input4
[ 3.611162] input: vc4-hdmi-0 as /devices/platform/soc@107c000000/107c701400.hdmi/rc/rc0/input5
[ 3.625459] videodev: Linux video capture interface: v2.00
[ 3.674688] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 3.677588] input: vc4-hdmi-0 HDMI Jack as /devices/platform/soc@107c000000/107c701400.hdmi/sound/card0/input6
[ 3.680959] Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
[ 3.681176] Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[ 3.681371] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 3.681562] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 3.683359] vc4-drm axi:gpu: bound 107c701400.hdmi (ops vc4_hdmi_ops [vc4])
[ 3.685723] Registered IR keymap rc-cec
[ 3.688927] rc rc1: vc4-hdmi-1 as /devices/platform/soc@107c000000/107c706400.hdmi/rc/rc1
[ 3.705762] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 3.705797] usbcore: registered new interface driver cdc_acm
[ 3.705799] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.706470] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 3.707257] input: vc4-hdmi-1 as /devices/platform/soc@107c000000/107c706400.hdmi/rc/rc1/input7
[ 3.707450] rp1-cfe 1f00128000.csi: bcm2712_iommu_of_xlate: MMU 1000005280.iommu
[ 3.707454] rp1-cfe 1f00128000.csi: bcm2712_iommu_probe_device: MMU 1000005280.iommu
[ 3.707460] rp1-cfe 1f00128000.csi: bcm2712_iommu_device_group: MMU 1000005280.iommu
[ 3.707467] rp1-cfe 1f00128000.csi: Adding to iommu group 2
[ 3.707472] rp1-cfe 1f00128000.csi: bcm2712_iommu_attach_dev: MMU 1000005280.iommu
[ 3.708241] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 3.710904] rp1-cfe 1f00128000.csi: DW dphy Host HW v1.20
[ 3.710928] rp1-cfe 1f00128000.csi: PiSP FE HW v0.1
[ 3.713260] rp1-cfe 1f00128000.csi: found subdevice /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 3.713554] usbcore: registered new interface driver brcmfmac
[ 3.713885] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 3.713896] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 3.714640] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 3.714884] rpi-hevc-dec 1000800000.codec: Adding to iommu group 0
[ 3.714891] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 3.725732] input: vc4-hdmi-1 HDMI Jack as /devices/platform/soc@107c000000/107c706400.hdmi/sound/card1/input8
[ 3.726760] vc4-drm axi:gpu: bound 107c706400.hdmi (ops vc4_hdmi_ops [vc4])
[ 3.726871] vc4-drm axi:gpu: bound 107c500000.mop (ops vc4_txp_ops [vc4])
[ 3.726913] vc4-drm axi:gpu: bound 107c501000.moplet (ops vc4_txp_ops [vc4])
[ 3.726958] vc4-drm axi:gpu: bound 107c410000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 3.727002] vc4-drm axi:gpu: bound 107c411000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 3.727430] pispbe 1000880000.pisp_be: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 3.727435] pispbe 1000880000.pisp_be: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 3.727441] pispbe 1000880000.pisp_be: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 3.727447] pispbe 1000880000.pisp_be: Adding to iommu group 0
[ 3.727449] pispbe 1000880000.pisp_be: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 3.757400] Bluetooth: Core ver 2.22
[ 3.757426] NET: Registered PF_BLUETOOTH protocol family
[ 3.757427] Bluetooth: HCI device and connection manager initialized
[ 3.757433] Bluetooth: HCI socket layer initialized
[ 3.757436] Bluetooth: L2CAP socket layer initialized
[ 3.757441] Bluetooth: SCO socket layer initialized
[ 3.801612] [drm] Initialized vc4 0.0.0 for axi:gpu on minor 1
[ 3.830370] Bluetooth: HCI UART driver ver 2.3
[ 3.830377] Bluetooth: HCI UART protocol H4 registered
[ 3.830396] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 3.830510] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
[ 3.830548] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
[ 3.830576] Bluetooth: HCI UART protocol Broadcom registered
[ 3.833615] rpi-hevc-dec 1000800000.codec: Device registered as /dev/video19
[ 3.902854] Console: switching to colour frame buffer device 320x90
[ 3.921184] vc4-drm axi:gpu: [drm] fb0: vc4drmfb frame buffer device
[ 4.066853] imx708 11-001a: camera module ID 0x0301
[ 4.070297] rp1-cfe 1f00128000.csi: Using sensor imx708 for capture
[ 4.077183] brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
[ 4.077481] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Aug 29 2023 01:47:08 version 7.45.265 (28bca26 CY) FWID 01-b677b91b
[ 4.081004] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-csi2_ch0] node id 0 successfully as /dev/video0
[ 4.082015] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-embedded] node id 1 successfully as /dev/video1
[ 4.082110] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-csi2_ch2] node id 2 successfully as /dev/video2
[ 4.082372] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-csi2_ch3] node id 3 successfully as /dev/video3
[ 4.082429] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_image0] node id 4 successfully as /dev/video4
[ 4.082487] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_image1] node id 5 successfully as /dev/video5
[ 4.082528] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_stats] node id 6 successfully as /dev/video6
[ 4.082557] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_config] node id 7 successfully as /dev/video7
[ 4.190065] Bluetooth: hci0: BCM: chip id 107
[ 4.190266] Bluetooth: hci0: BCM: features 0x2f
[ 4.191310] Bluetooth: hci0: BCM4345C0
[ 4.191313] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0000
[ 4.194346] Bluetooth: hci0: BCM4345C0 'brcm/BCM4345C0.raspberrypi,5-model-b.hcd' Patch
[ 4.560776] Adding 524272k swap on /var/swap. Priority:-2 extents:7 across:2228224k SS
[ 4.625547] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.625553] Bluetooth: BNEP filters: protocol multicast
[ 4.625559] Bluetooth: BNEP socket layer initialized
[ 4.874272] Bluetooth: hci0: BCM: features 0x2f
[ 4.875594] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+-0190
[ 4.875596] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0382
[ 4.875930] Bluetooth: hci0: BCM: Using default device address (m.m.m.m)
[ 4.892502] Bluetooth: MGMT ver 1.23
[ 4.902884] NET: Registered PF_ALG protocol family
[ 5.261143] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL)
[ 5.261154] macb 1f00100000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 5.265156] macb 1f00100000.ethernet: gem-ptp-timer ptp clock registered.
[ 5.297787] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 7.395211] Bluetooth: RFCOMM TTY layer initialized
[ 7.395236] Bluetooth: RFCOMM socket layer initialized
[ 7.395246] Bluetooth: RFCOMM ver 1.11
[ 2590.430362] usb 1-2: USB disconnect, device number 3
[ 2590.723896] usb 1-2: new full-speed USB device number 4 using xhci-hcd
[ 2590.883495] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 2590.883504] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2590.883507] usb 1-2: Product: Santiago DFU
[ 2590.883510] usb 1-2: Manufacturer: Arduino
[ 2590.883513] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2602.236691] usb 1-2: USB disconnect, device number 4
[ 2602.987917] usb 1-2: new full-speed USB device number 5 using xhci-hcd
[ 2603.148061] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 2603.148068] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2603.148071] usb 1-2: Product: UNO R4 Minima
[ 2603.148074] usb 1-2: Manufacturer: Arduino
[ 2603.148076] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2603.413144] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 2859.015796] usb 1-2: USB disconnect, device number 5
[ 2859.296147] usb 1-2: new full-speed USB device number 6 using xhci-hcd
[ 2859.455935] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 2859.455943] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2859.455945] usb 1-2: Product: Santiago DFU
[ 2859.455947] usb 1-2: Manufacturer: Arduino
[ 2859.455949] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2870.822124] usb 1-2: USB disconnect, device number 6
[ 2871.580138] usb 1-2: new full-speed USB device number 7 using xhci-hcd
[ 2871.740504] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 2871.740511] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2871.740513] usb 1-2: Product: UNO R4 Minima
[ 2871.740515] usb 1-2: Manufacturer: Arduino
[ 2871.740517] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2871.969569] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 3125.242116] usb 1-2: USB disconnect, device number 7
[ 3125.532098] usb 1-2: new full-speed USB device number 8 using xhci-hcd
[ 3125.691251] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 3125.691259] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3125.691261] usb 1-2: Product: Santiago DFU
[ 3125.691262] usb 1-2: Manufacturer: Arduino
[ 3125.691264] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3137.039498] usb 1-2: USB disconnect, device number 8
[ 3137.792088] usb 1-2: new full-speed USB device number 9 using xhci-hcd
[ 3137.952823] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 3137.952832] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3137.952836] usb 1-2: Product: UNO R4 Minima
[ 3137.952839] usb 1-2: Manufacturer: Arduino
[ 3137.952841] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3138.093904] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 3434.369422] usb 1-2: USB disconnect, device number 9
[ 3434.667838] usb 1-2: new full-speed USB device number 10 using xhci-hcd
[ 3434.827558] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 3434.827563] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3434.827565] usb 1-2: Product: Santiago DFU
[ 3434.827567] usb 1-2: Manufacturer: Arduino
[ 3434.827568] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3446.166744] usb 1-2: USB disconnect, device number 10
[ 3446.919826] usb 1-2: new full-speed USB device number 11 using xhci-hcd
[ 3447.080128] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 3447.080136] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3447.080138] usb 1-2: Product: UNO R4 Minima
[ 3447.080140] usb 1-2: Manufacturer: Arduino
[ 3447.080142] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3447.228185] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4018.856496] usb 1-2: USB disconnect, device number 11
[ 4019.143065] usb 1-2: new full-speed USB device number 12 using xhci-hcd
[ 4019.302640] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4019.302647] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4019.302650] usb 1-2: Product: Santiago DFU
[ 4019.302651] usb 1-2: Manufacturer: Arduino
[ 4019.302653] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4030.734810] usb 1-2: USB disconnect, device number 12
[ 4031.487044] usb 1-2: new full-speed USB device number 13 using xhci-hcd
[ 4031.647208] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4031.647216] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4031.647218] usb 1-2: Product: UNO R4 Minima
[ 4031.647220] usb 1-2: Manufacturer: Arduino
[ 4031.647221] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4031.831272] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4149.570545] usb 1-2: USB disconnect, device number 13
[ 4149.835082] usb 1-2: new full-speed USB device number 14 using xhci-hcd
[ 4149.994686] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4149.994695] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4149.994699] usb 1-2: Product: Santiago DFU
[ 4149.994702] usb 1-2: Manufacturer: Arduino
[ 4149.994704] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4161.450030] usb 1-2: USB disconnect, device number 14
[ 4162.207177] usb 1-2: new full-speed USB device number 15 using xhci-hcd
[ 4162.368262] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4162.368272] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4162.368275] usb 1-2: Product: UNO R4 Minima
[ 4162.368278] usb 1-2: Manufacturer: Arduino
[ 4162.368281] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4162.525423] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4218.034722] usb 1-2: USB disconnect, device number 15
[ 4218.319564] usb 1-2: new full-speed USB device number 16 using xhci-hcd
[ 4218.478862] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4218.478869] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4218.478871] usb 1-2: Product: Santiago DFU
[ 4218.478873] usb 1-2: Manufacturer: Arduino
[ 4218.478874] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4229.913106] usb 1-2: USB disconnect, device number 16
[ 4230.663646] usb 1-2: new full-speed USB device number 17 using xhci-hcd
[ 4230.824436] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4230.824443] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4230.824446] usb 1-2: Product: UNO R4 Minima
[ 4230.824448] usb 1-2: Manufacturer: Arduino
[ 4230.824449] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4231.008494] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4650.619805] usb 1-2: USB disconnect, device number 17
[ 4650.977392] usb 1-2: new full-speed USB device number 18 using xhci-hcd
[ 4651.136906] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4651.136912] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4651.136915] usb 1-2: Product: Santiago DFU
[ 4651.136916] usb 1-2: Manufacturer: Arduino
[ 4651.136918] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4662.507215] usb 1-2: USB disconnect, device number 18
[ 4663.265425] usb 1-2: new full-speed USB device number 19 using xhci-hcd
[ 4663.426474] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4663.426484] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4663.426488] usb 1-2: Product: UNO R4 Minima
[ 4663.426491] usb 1-2: Manufacturer: Arduino
[ 4663.426494] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4663.668654] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 5381.196613] usb 1-2: USB disconnect, device number 19
[ 5381.514116] usb 1-2: new full-speed USB device number 20 using xhci-hcd
[ 5381.673756] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 5381.673763] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5381.673766] usb 1-2: Product: Santiago DFU
[ 5381.673767] usb 1-2: Manufacturer: Arduino
[ 5381.673769] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 5393.083971] usb 1-2: USB disconnect, device number 20
[ 5393.842119] usb 1-2: new full-speed USB device number 21 using xhci-hcd
[ 5394.002332] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 5394.002340] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5394.002342] usb 1-2: Product: UNO R4 Minima
[ 5394.002344] usb 1-2: Manufacturer: Arduino
[ 5394.002346] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 5394.198386] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[17534.963569] usb 1-2: USB disconnect, device number 21
[17538.788378] usb 1-2: new full-speed USB device number 22 using xhci-hcd
[17538.948730] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[17538.948737] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[17538.948739] usb 1-2: Product: UNO R4 Minima
[17538.948741] usb 1-2: Manufacturer: Arduino
[17538.948743] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[17539.145796] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[17575.631316] usb 1-2: USB disconnect, device number 22
[17576.000377] usb 1-2: new full-speed USB device number 23 using xhci-hcd
[17576.160462] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[17576.160469] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[17576.160471] usb 1-2: Product: Santiago DFU
[17576.160473] usb 1-2: Manufacturer: Arduino
[17576.160474] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[17587.518738] usb 1-2: USB disconnect, device number 23
[17588.276367] usb 1-2: new full-speed USB device number 24 using xhci-hcd
[17588.437081] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[17588.437089] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[17588.437093] usb 1-2: Product: UNO R4 Minima
[17588.437096] usb 1-2: Manufacturer: Arduino
[17588.437098] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[17588.684173] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
EEPROM
------
BOOTLOADER: up to date
CURRENT: Thu May 8 02:13:17 PM UTC 2025 (1746713597)
LATEST: Thu May 8 02:13:17 PM UTC 2025 (1746713597)
RELEASE: default (/usr/lib/firmware/raspberrypi/bootloader-2712/default)
Use raspi-config to change the release.
initial_turbo=60
isp_freq=910
isp_freq_min=500
mask_gpu_interrupt1=16418
max_framebuffers=2
over_voltage_avs=0x19000
pause_burst_frames=1
pciex4_reset=1
pmic_turbo_threshold=1500
power_force_3v3_pwm=1
program_serial_random=1
total_mem=8192
usb_max_current_enable=1
v3d_freq=960
v3d_freq_min=500
vpred=8624
vpred_max=8624
hdmi_force_cec_address:0=65535
hdmi_force_cec_address:1=65535
device_tree=-
overlay_prefix=overlays/
hdmi_cvt:0=
hdmi_cvt:1=
hdmi_edid_filename:0=
hdmi_edid_filename:1=
hdmi_timings:0=
hdmi_timings:1=
cmdline.txt
-----------
reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe cgroup_disable=memory numa_policy=interleave nvme.max_host_mem_size_mb=0 numa=fake=8 system_heap.max_order=0 smsc95xx.macaddr=2C:CF:67:DF:54:42 vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000 console=ttyAMA10,115200 console=tty1 root=PARTUUID=82c49bc4-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=US
pin configuration
-----------------
0: ip pu | hi // ID_SDA/GPIO0 = input
1: ip pu | hi // ID_SCL/GPIO1 = input
2: no pu | -- // GPIO2 = none
3: no pu | -- // GPIO3 = none
4: no pu | -- // GPIO4 = none
5: no pu | -- // GPIO5 = none
6: no pu | -- // GPIO6 = none
7: no pu | -- // GPIO7 = none
8: no pu | -- // GPIO8 = none
9: no pd | -- // GPIO9 = none
10: no pd | -- // GPIO10 = none
11: no pd | -- // GPIO11 = none
12: no pd | -- // GPIO12 = none
13: no pd | -- // GPIO13 = none
14: no pd | -- // GPIO14 = none
15: no pd | -- // GPIO15 = none
16: no pd | -- // GPIO16 = none
17: no pd | -- // GPIO17 = none
18: no pd | -- // GPIO18 = none
19: no pd | -- // GPIO19 = none
20: no pd | -- // GPIO20 = none
21: no pd | -- // GPIO21 = none
22: no pd | -- // GPIO22 = none
23: no pd | -- // GPIO23 = none
24: no pd | -- // GPIO24 = none
25: no pd | -- // GPIO25 = none
26: no pd | -- // GPIO26 = none
27: no pd | -- // GPIO27 = none
28: no pd | lo // PCIE_RP1_WAKE/GPIO28 = none
29: no pu | lo // FAN_TACH/GPIO29 = none
30: no pu | -- // HOST_SDA/GPIO30 = none
31: no pu | -- // HOST_SCL/GPIO31 = none
32: op dh pd | hi // ETH_RST_N/GPIO32 = output
33: no pd | lo // GPIO33 = none
34: op dl pd | lo // CD0_IO0_MICCLK/GPIO34 = output
35: no pd | lo // CD0_IO0_MICDAT0/GPIO35 = none
36: no pd | lo // RP1_PCIE_CLKREQ_N/GPIO36 = none
37: no pd | lo // GPIO37 = none
38: ip pd | hi // CD0_SDA/GPIO38 = input
39: ip pd | hi // CD0_SCL/GPIO39 = input
40: a2 pu | hi // CD1_SDA/GPIO40 = SDA4
41: a2 pu | hi // CD1_SCL/GPIO41 = SCL4
42: a2 pd | hi // USB_VBUS_EN/GPIO42 = VBUS_EN1
43: a2 pu | hi // USB_OC_N/GPIO43 = VBUS_OC1
44: op dh pd | hi // RP1_STAT_LED/GPIO44 = output
45: a0 pd | lo // FAN_PWM/GPIO45 = PWM1_CHAN3
46: op dh pd | hi // CD1_IO0_MICCLK/GPIO46 = output
47: no pd | lo // 2712_WAKE/GPIO47 = none
48: no pd | lo // CD1_IO1_MICDAT1/GPIO48 = none
49: op dh pd | hi // EN_MAX_USB_CUR/GPIO49 = output
50: no pd | -- // GPIO50 = none
51: no pd | -- // GPIO51 = none
52: no pu | -- // GPIO52 = none
53: no pu | hi // GPIO53 = none
101: op dh pu | hi // 2712_BOOT_CS_N/GPIO1 = output
102: a7 pn | hi // 2712_BOOT_MISO/GPIO2 = VC_SPI0_MISO
103: a6 pn | hi // 2712_BOOT_MOSI/GPIO3 = VC_SPI0_MOSI
104: a6 pn | lo // 2712_BOOT_SCLK/GPIO4 = VC_SPI0_SCLK
110: ip pd | lo // GPIO10 = input
111: ip pd | lo // GPIO11 = input
112: ip pd | lo // GPIO12 = input
113: ip pd | lo // GPIO13 = input
114: a1 pd | lo // PCIE_SDA/GPIO14 = SPI_S_MOSI_OR_BSC_S_SDA
115: a1 pd | lo // PCIE_SCL/GPIO15 = SPI_S_SCK_OR_BSC_S_SCL
118: ip pd | lo // GPIO18 = input
119: ip pd | lo // GPIO19 = input
120: ip pu | hi // PWR_GPIO/GPIO20 = input
121: ip pd | lo // 2712_G21_FS/GPIO21 = input
122: ip pu | hi // GPIO22 = input
123: ip pd | lo // GPIO23 = input
124: a4 pn | lo // BT_RTS/GPIO24 = UART_RTS_0
125: a4 pu | lo // BT_CTS/GPIO25 = UART_CTS_0
126: a4 pn | hi // BT_TXD/GPIO26 = UART_TXD_0
127: a4 pu | hi // BT_RXD/GPIO27 = UART_RXD_0
128: op dh pd | hi // WL_ON/GPIO28 = output
129: op dh pd | hi // BT_ON/GPIO29 = output
130: a1 pn | hi // WIFI_SDIO_CLK/GPIO30 = SD2_CLK
131: a1 pu | hi // WIFI_SDIO_CMD/GPIO31 = SD2_CMD
132: a1 pu | hi // WIFI_SDIO_D0/GPIO32 = SD2_DAT0
133: a1 pu | hi // WIFI_SDIO_D1/GPIO33 = SD2_DAT1
134: a1 pu | hi // WIFI_SDIO_D2/GPIO34 = SD2_DAT2
135: a1 pu | hi // WIFI_SDIO_D3/GPIO35 = SD2_DAT3
200: ip pd | hi // RP1_SDA/AON_GPIO0 = input
201: ip pd | hi // RP1_SCL/AON_GPIO1 = input
202: op dh pd | hi // RP1_RUN/AON_GPIO2 = output
203: op dh pd | hi // SD_IOVDD_SEL/AON_GPIO3 = output
204: op dh pd | hi // SD_PWR_ON/AON_GPIO4 = output
205: a4 pu | lo // SD_CDET_N/AON_GPIO5 = SD_CARD_PRES_G
206: ip pd | hi // SD_FLG_N/AON_GPIO6 = input
208: ip pd | lo // 2712_WAKE/AON_GPIO8 = input
209: op dh pd | hi // 2712_STAT_LED/AON_GPIO9 = output
212: ip pd | lo // PMIC_INT/AON_GPIO12 = input
213: a2 pu | hi // UART_TX_FS/AON_GPIO13 = VC_TXD0
214: a3 pu | hi // UART_RX_FS/AON_GPIO14 = VC_RXD0
232: a1 -- | hi // HDMI0_SCL/AON_SGPIO0 = HDMI_TX0_BSC_SCL
233: a1 -- | hi // HDMI0_SDA/AON_SGPIO1 = HDMI_TX0_BSC_SDA
234: a1 -- | hi // HDMI1_SCL/AON_SGPIO2 = HDMI_TX1_BSC_SCL
235: a1 -- | hi // HDMI1_SDA/AON_SGPIO3 = HDMI_TX1_BSC_SDA
236: a2 -- | hi // PMIC_SCL/AON_SGPIO4 = BSC_M2_SCL
237: a2 -- | hi // PMIC_SDA/AON_SGPIO5 = BSC_M2_SDA
vcdbg log messages
------------------
004938.840: *** Restart logging
004953.155: Initial voltage 800000 temp 23541
005153.604: avs_2712: AVS pred 8624 862400 temp 22991
005157.206: vpred 862 mV +0
005965.333: FB framebuffer_swap 1
005984.711: Select resolution HDMI0/2 hotplug 1 max_mode 2
006001.138: HDMI0 edid block 0 offset 0
006003.522: 00ffffffffffff0010acc2d054554b31
006009.194: 281c010380351e78eaad75a9544d9d26
006014.866: 0f5054a54b008100b300d100714fa940
006020.539: 8180d1c00101565e00a0a0a029503020
006026.212: 35000e282100001a000000ff0032394a
006031.885: 3050384135314b55540a000000fc0044
006037.558: 454c4c205032343138440a20000000fd
006043.231: 0031561d711c000a202020202020012b
006061.285: HDMI0 edid block 1 offset 128
006063.841: 02031bb1509005040302071601061112
006069.513: 1513141f2065030c001000023a801871
006075.186: 382d40582c45000e282100001e011d80
006080.859: 18711c1620582c25000e282100009ebf
006086.532: 1600a08038134030203a000e28210000
006092.205: 1a7e3900a080381f4030203a000e2821
006097.877: 00001a00000000000000000000000000
006103.550: 000000000000000000000000000000d8
006109.242: HDMI0: best-mode 2 (limit 2) 1920x1080 60 Hz CEA modes fe007f80010000000000000000000000 extensions 1
006120.835: Select resolution HDMI1/2 hotplug 0 max_mode 2
006127.757: FB0 disp 0 max-fb 2 1920x1080 stride 3840 base 0x3f800000
006787.175: initramfs (initramfs_2712) loaded to 0x2e350000 (size 0xcaf765)
006802.158: dtb_file 'bcm2712-rpi-5-b.dtb'
006885.989: Loaded overlay 'bcm2712d0'
006959.748: Found camera 'imx708' on port 1, unicam_port 1
007033.423: Loaded overlay 'imx708'
007151.995: dtparam: audio=on
007160.580: Unknown dtparam 'audio' - ignored
007231.324: Loaded overlay 'vc4-kms-v3d-pi5'
007404.676: Read command line from file 'cmdline.txt':
007411.177: 'console=serial0,115200 console=tty1 root=PARTUUID=82c49bc4-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=US'
007633.488: RPM 5914, max RPM 5914
009518.889: Device tree loaded to 0x2e33c200 (size 0x13d30)
009592.365: Starting OS 9592 ms
009597.890: 00000040: -> 00000480
009599.739: 00000030: -> 00100080
009604.452: 00000034: -> 00100080
009609.165: 00000038: -> 00100080
009613.877: 0000003c: -> 00100080
009723.453: sdram: sdram refresh 2081->8324 (1)
069682.262: initial_turbo of 60 deactivated
240554.507: sdram: sdram refresh 2081->4162 (2)
dmesg log
---------
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1]
[ 0.000000] Linux version 6.12.34+rpt-rpi-2712 (serge@raspberrypi.com) (aarch64-linux-gnu-gcc-12 (Debian 12.2.0-14+deb12u1) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Debian 1:6.12.34-1+rpt1~bookworm (2025-06-26)
[ 0.000000] KASLR enabled
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Raspberry Pi 5 Model B Rev 1.1
[ 0.000000] efi: UEFI not found.
** some deleted lines here to get within the character limit **
[ 0.003155] rcu: Hierarchical SRCU implementation.
[ 0.003161] rcu: Max phase no-delay instances is 1000.
[ 0.003201] Timer migration: 1 hierarchy levels; 8 children per group; 0 crossnode level
[ 0.003554] EFI services will not be available.
[ 0.003622] smp: Bringing up secondary CPUs ...
[ 0.003804] Detected PIPT I-cache on CPU1
[ 0.003842] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1]
[ 0.004079] Detected PIPT I-cache on CPU2
[ 0.004105] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1]
[ 0.004297] Detected PIPT I-cache on CPU3
[ 0.004316] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1]
[ 0.004346] smp: Brought up 8 nodes, 4 CPUs
[ 0.004352] SMP: Total of 4 processors activated.
[ 0.004354] CPU: All CPU(s) started at EL2
[ 0.004356] CPU features: detected: 32-bit EL0 Support
[ 0.004358] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.004359] CPU features: detected: Common not Private translations
[ 0.004360] CPU features: detected: CRC32 instructions
[ 0.004363] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.004365] CPU features: detected: LSE atomic instructions
[ 0.004366] CPU features: detected: Privileged Access Never
[ 0.004367] CPU features: detected: RAS Extension Support
[ 0.004368] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.004393] alternatives: applying system-wide alternatives
[ 0.005794] CPU features: detected: Hardware dirty bit management on CPU0-3
[ 0.005968] Memory: 8141888K/8380416K available (14208K kernel code, 2418K rwdata, 4928K rodata, 5696K init, 647K bss, 146464K reserved, 65536K cma-reserved)
[ 0.006139] devtmpfs: initialized
[ 0.008044] Enabled cp15_barrier support
[ 0.008049] Enabled setend support
[ 0.008087] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.008092] futex hash table entries: 1024 (order: 2, 65536 bytes, vmalloc)
[ 0.008206] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
[ 0.008207] 0 pages in range for non-PLT usage
[ 0.008208] 129308 pages in range for PLT usage
[ 0.008288] pinctrl core: initialized pinctrl subsystem
[ 0.008411] DMI not present or invalid.
[ 0.012475] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.012806] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.012834] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.012863] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.012876] audit: initializing netlink subsys (disabled)
[ 0.012932] audit: type=2000 audit(0.012:1): state=initialized audit_enabled=0 res=1
[ 0.013025] thermal_sys: Registered thermal governor 'step_wise'
[ 0.013034] cpuidle: using governor menu
[ 0.013089] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.013108] ASID allocator initialised with 32768 entries
[ 0.013358] Serial: AMBA PL011 UART driver
[ 0.014092] /soc@107c000000/interrupt-controller@7fff9000: Fixed dependency cycle(s) with /soc@107c000000/interrupt-controller@7fff9000
[ 0.014247] bcm2835-mbox 107c013880.mailbox: mailbox enabled
[ 0.014364] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 16, base_baud = 0) is a PL011 rev3
[ 0.014373] printk: legacy console [ttyAMA10] enabled
[ 0.020010] raspberrypi-firmware soc@107c000000:firmware: Attached to firmware from 2025-05-08T14:13:17, variant start_cd
[ 0.024010] raspberrypi-firmware soc@107c000000:firmware: Firmware hash is 6947117700000000000000000000000000000000
[ 0.028979] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.029005] /axi/pcie@1000120000/rp1/csi@128000: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 0.029118] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.029145] /axi/pcie@1000120000/rp1/csi@128000: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 0.032625] bcm2835-dma 1000010000.dma: DMA legacy API manager, dmachans=0x1
[ 0.032874] iommu: Default domain type: Translated
[ 0.032876] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.033188] SCSI subsystem initialized
[ 0.033218] usbcore: registered new interface driver usbfs
[ 0.033224] usbcore: registered new interface driver hub
[ 0.033229] usbcore: registered new device driver usb
[ 0.033294] pps_core: LinuxPPS API ver. 1 registered
[ 0.033295] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.033298] PTP clock support registered
[ 0.033545] vgaarb: loaded
[ 0.033630] clocksource: Switched to clocksource arch_sys_counter
[ 0.239502] VFS: Disk quotas dquot_6.6.0
[ 0.239508] VFS: Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
[ 0.240674] NET: Registered PF_INET protocol family
[ 0.240812] IP idents hash table entries: 131072 (order: 6, 1048576 bytes, vmalloc)
[ 0.242375] tcp_listen_portaddr_hash hash table entries: 4096 (order: 2, 65536 bytes, vmalloc)
[ 0.242401] Table-perturb hash table entries: 65536 (order: 4, 262144 bytes, vmalloc)
[ 0.242408] TCP established hash table entries: 65536 (order: 5, 524288 bytes, vmalloc)
[ 0.242607] TCP bind hash table entries: 65536 (order: 7, 2097152 bytes, vmalloc)
[ 0.243263] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.243363] MPTCP token hash table entries: 8192 (order: 3, 196608 bytes, vmalloc)
[ 0.243399] UDP hash table entries: 4096 (order: 3, 131072 bytes, vmalloc)
[ 0.243463] UDP-Lite hash table entries: 4096 (order: 3, 131072 bytes, vmalloc)
[ 0.243559] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.243719] RPC: Registered named UNIX socket transport module.
[ 0.243721] RPC: Registered udp transport module.
[ 0.243722] RPC: Registered tcp transport module.
[ 0.243723] RPC: Registered tcp-with-tls transport module.
[ 0.243725] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.243729] PCI: CLS 0 bytes, default 64
[ 0.243831] Trying to unpack rootfs image as initramfs...
[ 0.246706] kvm [1]: nv: 554 coarse grained trap handlers
[ 0.246800] kvm [1]: IPA Size Limit: 40 bits
[ 0.246816] kvm [1]: GICV region size/alignment is unsafe, using trapping (reduced performance)
[ 0.246876] kvm [1]: vgic interrupt IRQ9
[ 0.246888] kvm [1]: VHE mode initialized successfully
[ 0.247376] Initialise system trusted keyrings
[ 0.249796] workingset: timestamp_bits=42 max_order=19 bucket_order=0
[ 0.250106] NFS: Registering the id_resolver key type
[ 0.250113] Key type id_resolver registered
[ 0.250114] Key type id_legacy registered
[ 0.250123] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.250126] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.250299] Key type asymmetric registered
[ 0.250301] Asymmetric key parser 'x509' registered
[ 0.250320] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.250351] io scheduler mq-deadline registered
[ 0.250354] io scheduler kyber registered
[ 0.250373] io scheduler bfq registered
[ 0.250704] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/interrupt-controller@7d510600, parent irq: 27)
[ 0.250736] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/interrupt-controller@7c502000, parent irq: 28)
[ 0.250764] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508380, parent irq: 29)
[ 0.250800] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508400, parent irq: 30)
[ 0.250827] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d503000, parent irq: 31)
[ 0.251737] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.347544] Freeing initrd memory: 12976K
[ 0.348362] simple-framebuffer 3f800000.framebuffer: framebuffer at 0x3f800000, 0x3f4800 bytes
[ 0.348371] simple-framebuffer 3f800000.framebuffer: format=r5g6b5, mode=1920x1080x16, linelength=3840
[ 0.348606] Console: switching to colour frame buffer device 240x67
[ 0.350036] simple-framebuffer 3f800000.framebuffer: fb0: simplefb registered!
[ 0.379658] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 0.379949] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 33, base_baud = 6000000) is a Broadcom BCM7271 UART
[ 0.379988] serial serial0: tty port ttyS0 registered
[ 0.380252] iproc-rng200 107d208000.rng: hwrng registered
[ 0.380282] vc-mem: phys_addr:0x00000000 mem_base=0x3fc00000 mem_size:0x40000000(1024 MiB)
[ 0.380460] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe
[ 0.381737] brd: module loaded
[ 0.382560] loop: module loaded
[ 0.382652] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[ 0.382750] Loading iSCSI transport class v2.0-870.
[ 0.383427] usbcore: registered new interface driver lan78xx
[ 0.383434] usbcore: registered new interface driver smsc95xx
[ 0.383479] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.383493] dwc_otg: FIQ enabled
[ 0.383495] dwc_otg: NAK holdoff enabled
[ 0.383496] dwc_otg: FIQ split-transaction FSM enabled
[ 0.383498] Module dwc_common_port init
[ 0.383692] usbcore: registered new interface driver uas
[ 0.383700] usbcore: registered new interface driver usb-storage
[ 0.383766] mousedev: PS/2 mouse device common for all mice
[ 0.391296] rpi-rtc soc@107c000000:rpi_rtc: registered as rtc0
[ 0.392678] rpi-rtc soc@107c000000:rpi_rtc: setting system clock to 1970-01-01T00:00:10 UTC (10)
[ 0.392962] bcm2835-wdt bcm2835-wdt: Poweroff handler already present!
[ 0.392964] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.394957] sdhci: Secure Digital Host Controller Interface driver
[ 0.394959] sdhci: Copyright(c) Pierre Ossman
[ 0.394987] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.395050] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 0.395059] hid: raw HID events driver (C) Jiri Kosina
[ 0.395075] usbcore: registered new interface driver usbhid
[ 0.395077] usbhid: USB HID core driver
[ 0.395351] hw perfevents: enabled with armv8_cortex_a76 PMU driver, 7 (0,8000003f) counters available
[ 0.395556] NET: Registered PF_PACKET protocol family
[ 0.395576] Key type dns_resolver registered
[ 0.398967] registered taskstats version 1
[ 0.399028] Loading compiled-in X.509 certificates
[ 0.400431] Demotion targets for Node 0: null
[ 0.400434] Demotion targets for Node 1: null
[ 0.400435] Demotion targets for Node 2: null
[ 0.400436] Demotion targets for Node 3: null
[ 0.400437] Demotion targets for Node 4: null
[ 0.400438] Demotion targets for Node 5: null
[ 0.400439] Demotion targets for Node 6: null
[ 0.400440] Demotion targets for Node 7: null
[ 0.400594] Key type .fscrypt registered
[ 0.400596] Key type fscrypt-provisioning registered
[ 0.401433] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@1000120000 ranges:
[ 0.401437] brcm-pcie 1000120000.pcie: No bus range found for /axi/pcie@1000120000, using [bus 00-ff]
[ 0.401445] brcm-pcie 1000120000.pcie: MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000
[ 0.401449] brcm-pcie 1000120000.pcie: MEM 0x1c00000000..0x1effffffff -> 0x0400000000
[ 0.401454] brcm-pcie 1000120000.pcie: IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000
[ 0.401459] brcm-pcie 1000120000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[ 0.401462] brcm-pcie 1000120000.pcie: IB MEM 0x1000130000..0x1000130fff -> 0xfffffff000
[ 0.402774] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0002:00
[ 0.402778] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 0.402780] pci_bus 0002:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb])
[ 0.402783] pci_bus 0002:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff])
[ 0.402794] pci 0002:00:00.0: [14e4:2712] type 01 class 0x060400 PCIe Root Port
[ 0.402799] pci 0002:00:00.0: PCI bridge to [bus 00]
[ 0.402802] pci 0002:00:00.0: bridge window [mem 0x1f80000000-0x1fbfffffff]
[ 0.402818] pci 0002:00:00.0: PME# supported from D0 D3hot
[ 0.403429] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.505633] brcm-pcie 1000120000.pcie: clkreq-mode set to default
[ 0.505636] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC)
[ 0.505656] pci 0002:01:00.0: [1de4:0001] type 00 class 0x020000 PCIe Endpoint
[ 0.505669] pci 0002:01:00.0: BAR 0 [mem 0xffffc000-0xffffffff]
[ 0.505675] pci 0002:01:00.0: BAR 1 [mem 0xffc00000-0xffffffff]
[ 0.505681] pci 0002:01:00.0: BAR 2 [mem 0xffff0000-0xffffffff]
[ 0.505743] pci 0002:01:00.0: supports D1
[ 0.505744] pci 0002:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.513639] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.513647] pci 0002:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]: assigned
[ 0.513650] pci 0002:01:00.0: BAR 1 [mem 0x1f00000000-0x1f003fffff]: assigned
[ 0.513654] pci 0002:01:00.0: BAR 2 [mem 0x1f00400000-0x1f0040ffff]: assigned
[ 0.513657] pci 0002:01:00.0: BAR 0 [mem 0x1f00410000-0x1f00413fff]: assigned
[ 0.513662] pci 0002:00:00.0: PCI bridge to [bus 01]
[ 0.513664] pci 0002:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]
[ 0.513666] pci_bus 0002:00: resource 4 [mem 0x1f00000000-0x1ffffffffb]
[ 0.513669] pci_bus 0002:00: resource 5 [mem 0x1c00000000-0x1effffffff pref]
[ 0.513671] pci_bus 0002:01: resource 1 [mem 0x1f00000000-0x1f005fffff]
[ 0.513674] pci 0002:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512
[ 0.513681] pci 0002:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512
[ 0.513739] pcieport 0002:00:00.0: enabling device (0000 -> 0002)
[ 0.513764] pcieport 0002:00:00.0: PME: Signaling with IRQ 38
[ 0.513804] pcieport 0002:00:00.0: AER: enabled with IRQ 38
[ 0.513859] rp1 0002:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200
[ 0.513862] rp1 0002:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200
[ 0.513873] rp1 0002:01:00.0: enabling device (0000 -> 0002)
[ 0.514463] rp1 0002:01:00.0: chip_id 0x20001927
[ 0.518069] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.518467] genirq: irq_chip rp1_irq_chip did not update eff. affinity mask of irq 100
[ 0.533127] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 106 (m.m.m.m)
[ 0.533189] /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/csi@128000
[ 0.533207] /axi/pcie@1000120000/rp1/csi@128000: Fixed dependency cycle(s) with /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 0.533992] dw_axi_dmac_platform 1f00188000.dma: DesignWare AXI DMA Controller, 8 channels
[ 0.534212] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.534217] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
[ 0.534652] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810
[ 0.534660] xhci-hcd xhci-hcd.0: irq 131, io mem 0x1f00200000
[ 0.534715] xhci-hcd xhci-hcd.0: xHCI Host Controller
[ 0.534717] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
[ 0.534719] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed
[ 0.534758] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 0.534761] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.534763] usb usb1: Product: xHCI Host Controller
[ 0.534765] usb usb1: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.534766] usb usb1: SerialNumber: xhci-hcd.0
[ 0.534863] hub 1-0:1.0: USB hub found
[ 0.534876] hub 1-0:1.0: 2 ports detected
[ 0.534969] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 0.534971] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.534973] usb usb2: Product: xHCI Host Controller
[ 0.534975] usb usb2: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.534976] usb usb2: SerialNumber: xhci-hcd.0
[ 0.535036] hub 2-0:1.0: USB hub found
[ 0.535046] hub 2-0:1.0: 1 port detected
[ 0.535254] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.535258] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3
[ 0.535683] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810
[ 0.535691] xhci-hcd xhci-hcd.1: irq 136, io mem 0x1f00300000
[ 0.535742] xhci-hcd xhci-hcd.1: xHCI Host Controller
[ 0.535744] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4
[ 0.535746] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed
[ 0.535770] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 0.535772] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.535774] usb usb3: Product: xHCI Host Controller
[ 0.535776] usb usb3: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.535777] usb usb3: SerialNumber: xhci-hcd.1
[ 0.535836] hub 3-0:1.0: USB hub found
[ 0.535846] hub 3-0:1.0: 2 ports detected
[ 0.535927] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 0.535930] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.535932] usb usb4: Product: xHCI Host Controller
[ 0.535933] usb usb4: Manufacturer: Linux 6.12.34+rpt-rpi-2712 xhci-hcd
[ 0.535935] usb usb4: SerialNumber: xhci-hcd.1
[ 0.535991] hub 4-0:1.0: USB hub found
[ 0.536001] hub 4-0:1.0: 1 port detected
[ 0.536729] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.537088] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success
[ 0.537499] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.537866] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success
[ 0.538247] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[ 0.538591] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success
[ 0.538798] sdhci-brcmstb 1000fff000.mmc: Got CD GPIO
[ 0.538885] mmc0: CQHCI version 5.10
[ 0.539124] mmc1: CQHCI version 5.10
[ 0.540064] of_cfs_init
[ 0.540097] of_cfs_init: OK
[ 0.540250] clk: Disabling unused clocks
[ 0.548945] PM: genpd: Disabling unused power domains
[ 0.577003] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit
[ 0.679901] mmc0: Command Queue Engine enabled, 31 tags
[ 0.679905] mmc0: new ultra high speed SDR104 SDHC card at address 59b4
[ 0.680053] mmcblk0: mmc0:59b4 USD00 29.5 GiB
[ 0.680825] mmcblk0: p1 p2
[ 0.680882] mmcblk0: mmc0:59b4 USD00 29.5 GiB (quirks 0x40000000)
[ 0.724168] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit
[ 0.727026] Freeing unused kernel memory: 5696K
[ 0.727123] Run /init as init process
[ 0.727125] with arguments:
[ 0.727126] /init
[ 0.727127] splash
[ 0.727128] with environment:
[ 0.727129] HOME=/
[ 0.727130] TERM=linux
[ 0.756889] mmc1: new ultra high speed DDR50 SDIO card at address 0001
[ 0.781639] usb 1-1: new low-speed USB device number 2 using xhci-hcd
[ 0.785637] usb 3-2: new low-speed USB device number 2 using xhci-hcd
[ 0.824971] v3d 1002000000.v3d: [drm] Transparent Hugepage support is recommended for optimal performance on this platform!
[ 0.829876] [drm] Initialized v3d 1.0.0 for 1002000000.v3d on minor 0
[ 0.834721] vc4_hvs 107c580000.hvs: bcm2712_iommu_of_xlate: MMU 1000005200.iommu
[ 0.834727] vc4_hvs 107c580000.hvs: bcm2712_iommu_probe_device: MMU 1000005200.iommu
[ 0.834733] vc4_hvs 107c580000.hvs: bcm2712_iommu_device_group: MMU 1000005200.iommu
[ 0.834738] vc4_hvs 107c580000.hvs: Adding to iommu group 1
[ 0.834741] vc4_hvs 107c580000.hvs: bcm2712_iommu_attach_dev: MMU 1000005200.iommu
[ 0.836772] vc4-drm axi:gpu: bcm2712_iommu_of_xlate: MMU 1000005200.iommu
[ 0.836779] vc4-drm axi:gpu: bcm2712_iommu_probe_device: MMU 1000005200.iommu
[ 0.836783] vc4-drm axi:gpu: bcm2712_iommu_device_group: MMU 1000005200.iommu
[ 0.836787] vc4-drm axi:gpu: Adding to iommu group 1
[ 0.836790] vc4-drm axi:gpu: bcm2712_iommu_attach_dev: MMU 1000005200.iommu
[ 0.837411] Console: switching to colour dummy device 80x25
[ 0.843069] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 0.950865] usb 3-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00
[ 0.950873] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 0.950875] usb 3-2: Product: USB Optical Mouse
[ 0.950877] usb 3-2: Manufacturer: Logitech
[ 0.953838] usb 1-1: New USB device found, idVendor=046d, idProduct=c31c, bcdDevice=64.00
[ 0.953841] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 0.953843] usb 1-1: Product: USB Keyboard
[ 0.953844] usb 1-1: Manufacturer: Logitech
[ 0.983826] input: Logitech USB Optical Mouse as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.0/0003:046D:C077.0001/input/input0
[ 0.983896] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.1-2/input0
[ 0.987318] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 1.430840] input: Logitech USB Keyboard as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1:1.0/0003:046D:C31C.0002/input/input1
[ 1.549685] hid-generic 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.0-1/input0
[ 1.552000] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 1.686765] input: Logitech USB Keyboard Consumer Control as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1:1.1/0003:046D:C31C.0003/input/input2
[ 1.741677] input: Logitech USB Keyboard System Control as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1:1.1/0003:046D:C31C.0003/input/input3
[ 1.741718] hid-generic 0003:046D:C31C.0003: input,hidraw2: USB HID v1.10 Device [Logitech USB Keyboard] on usb-xhci-hcd.0-1/input1
[ 1.743965] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 1.861632] usb 1-2: new full-speed USB device number 3 using xhci-hcd
[ 2.021826] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 2.021829] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.021831] usb 1-2: Product: UNO R4 Minima
[ 2.021832] usb 1-2: Manufacturer: Arduino
[ 2.021834] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2.208192] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 2.309863] EXT4-fs (mmcblk0p2): mounted filesystem a36be96c-66be-4487-a7a6-0481bca99d89 ro with ordered data mode. Quota mode: none.
[ 2.533127] systemd[1]: System time before build time, advancing clock.
[ 2.581850] NET: Registered PF_INET6 protocol family
[ 2.582172] Segment Routing with IPv6
[ 2.582180] In-situ OAM (IOAM) with IPv6
[ 2.603478] systemd[1]: systemd 252.38-1~deb12u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[ 2.603489] systemd[1]: Detected architecture arm64.
[ 2.609317] systemd[1]: Hostname set to <raspberrypi>.
[ 2.863329] systemd[1]: Queued start job for default target graphical.target.
[ 2.882046] systemd[1]: Created slice system-getty.slice - Slice /system/getty.
[ 2.882249] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe.
[ 2.882412] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty.
[ 2.882571] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck.
[ 2.882662] systemd[1]: Created slice user.slice - User and Session Slice.
[ 2.882711] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch.
[ 2.882838] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point.
[ 2.882857] systemd[1]: Expecting device dev-disk-by\x2dpartuuid-82c49bc4\x2d01.device - /dev/disk/by-partuuid/82c49bc4-01...
[ 2.882866] systemd[1]: Expecting device dev-dri-card0.device - /dev/dri/card0...
[ 2.882872] systemd[1]: Expecting device dev-dri-renderD128.device - /dev/dri/renderD128...
[ 2.882879] systemd[1]: Expecting device dev-ttyAMA10.device - /dev/ttyAMA10...
[ 2.882901] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes.
[ 2.882926] systemd[1]: Reached target nss-user-lookup.target - User and Group Name Lookups.
[ 2.882948] systemd[1]: Reached target slices.target - Slice Units.
[ 2.882965] systemd[1]: Reached target swap.target - Swaps.
[ 2.882984] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes.
[ 2.883092] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket.
[ 2.883136] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe.
[ 2.883310] systemd[1]: Listening on systemd-journald-audit.socket - Journal Audit Socket.
[ 2.883388] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[ 2.883471] systemd[1]: Listening on systemd-journald.socket - Journal Socket.
[ 2.883832] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket.
[ 2.883902] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[ 2.884003] systemd[1]: dev-hugepages.mount - Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[ 2.884516] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System...
[ 2.885140] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System...
[ 2.885811] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System...
[ 2.885957] systemd[1]: auth-rpcgss-module.service - Kernel Module supporting RPCSEC_GSS was skipped because of an unmet condition check (ConditionPathExists=/etc/krb5.keytab).
[ 2.887343] systemd[1]: Starting fake-hwclock.service - Restore / save the current clock...
[ 2.888188] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout...
[ 2.888990] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes...
[ 2.890237] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs...
[ 2.891346] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod...
[ 2.892869] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm...
[ 2.894254] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore...
[ 2.895315] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse...
[ 2.896472] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop...
[ 2.896630] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root).
[ 2.898306] systemd[1]: Starting systemd-journald.service - Journal Service...
[ 2.905791] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules...
[ 2.906625] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems...
[ 2.907410] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices...
[ 2.908725] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System.
[ 2.909054] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System.
[ 2.909235] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System.
[ 2.910023] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev
[ 2.910242] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes.
[ 2.910659] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 2.910747] systemd[1]: Finished modprobe@configfs.service - Load Kernel Module configfs.
[ 2.910914] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[ 2.910987] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod.
[ 2.911137] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 2.911203] systemd[1]: Finished modprobe@drm.service - Load Kernel Module drm.
[ 2.911357] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[ 2.911427] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore.
[ 2.911575] systemd[1]: modprobe@loop.service: Deactivated successfully.
[ 2.911642] systemd[1]: Finished modprobe@loop.service - Load Kernel Module loop.
[ 2.912624] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System...
[ 2.912734] systemd[1]: systemd-repart.service - Repartition Root Disk was skipped because no trigger condition checks were met.
[ 2.914469] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System.
[ 2.922808] fuse: init (API version 7.41)
[ 2.923405] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[ 2.923508] systemd[1]: Finished modprobe@fuse.service - Load Kernel Module fuse.
[ 2.924233] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System...
[ 2.925980] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System.
[ 2.936190] systemd[1]: Finished fake-hwclock.service - Restore / save the current clock.
[ 2.945897] i2c_dev: i2c /dev entries driver
[ 2.946433] systemd[1]: Started systemd-journald.service - Journal Service.
[ 2.949766] EXT4-fs (mmcblk0p2): re-mounted a36be96c-66be-4487-a7a6-0481bca99d89 r/w.
[ 2.962673] systemd-journald[311]: Received client request to flush runtime journal.
[ 2.976655] systemd-journald[311]: File /var/log/journal/cb792f53419845d3b17675f494f0e038/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 3.550208] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.552607] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040
[ 3.552673] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1
[ 3.552818] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040
[ 3.556193] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2
[ 3.556225] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020
[ 3.562267] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3
[ 3.566267] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020
[ 3.566402] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4
[ 3.567633] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000
[ 3.567714] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0
[ 3.568837] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.572862] rp1-firmware rp1_firmware: RP1 Firmware version eb39cfd516f8c90628aa9d91f52370aade5d0a55
[ 3.576887] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.581413] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.593788] mc: Linux media interface: v0.10
[ 3.593837] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.604795] brcmstb-i2c 107d508200.i2c: @97500hz registered in interrupt mode
[ 3.605607] brcmstb-i2c 107d508280.i2c: @97500hz registered in interrupt mode
[ 3.607182] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops [vc4])
[ 3.609155] rp1-pio 1f00178000.pio: Created instance as pio0
[ 3.609173] Registered IR keymap rc-cec
[ 3.609200] rc rc0: vc4-hdmi-0 as /devices/platform/soc@107c000000/107c701400.hdmi/rc/rc0
[ 3.611015] input: pwr_button as /devices/platform/pwr_button/input/input4
[ 3.611162] input: vc4-hdmi-0 as /devices/platform/soc@107c000000/107c701400.hdmi/rc/rc0/input5
[ 3.625459] videodev: Linux video capture interface: v2.00
[ 3.674688] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 3.677588] input: vc4-hdmi-0 HDMI Jack as /devices/platform/soc@107c000000/107c701400.hdmi/sound/card0/input6
[ 3.680959] Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf'
[ 3.681176] Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328'
[ 3.681371] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 3.681562] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 3.683359] vc4-drm axi:gpu: bound 107c701400.hdmi (ops vc4_hdmi_ops [vc4])
[ 3.685723] Registered IR keymap rc-cec
[ 3.688927] rc rc1: vc4-hdmi-1 as /devices/platform/soc@107c000000/107c706400.hdmi/rc/rc1
[ 3.705762] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 3.705797] usbcore: registered new interface driver cdc_acm
[ 3.705799] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.706470] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 3.707257] input: vc4-hdmi-1 as /devices/platform/soc@107c000000/107c706400.hdmi/rc/rc1/input7
[ 3.707450] rp1-cfe 1f00128000.csi: bcm2712_iommu_of_xlate: MMU 1000005280.iommu
[ 3.707454] rp1-cfe 1f00128000.csi: bcm2712_iommu_probe_device: MMU 1000005280.iommu
[ 3.707460] rp1-cfe 1f00128000.csi: bcm2712_iommu_device_group: MMU 1000005280.iommu
[ 3.707467] rp1-cfe 1f00128000.csi: Adding to iommu group 2
[ 3.707472] rp1-cfe 1f00128000.csi: bcm2712_iommu_attach_dev: MMU 1000005280.iommu
[ 3.708241] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 3.710904] rp1-cfe 1f00128000.csi: DW dphy Host HW v1.20
[ 3.710928] rp1-cfe 1f00128000.csi: PiSP FE HW v0.1
[ 3.713260] rp1-cfe 1f00128000.csi: found subdevice /axi/pcie@1000120000/rp1/i2c@80000/imx708@1a
[ 3.713554] usbcore: registered new interface driver brcmfmac
[ 3.713885] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 3.713896] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 3.714640] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 3.714884] rpi-hevc-dec 1000800000.codec: Adding to iommu group 0
[ 3.714891] rpi-hevc-dec 1000800000.codec: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 3.725732] input: vc4-hdmi-1 HDMI Jack as /devices/platform/soc@107c000000/107c706400.hdmi/sound/card1/input8
[ 3.726760] vc4-drm axi:gpu: bound 107c706400.hdmi (ops vc4_hdmi_ops [vc4])
[ 3.726871] vc4-drm axi:gpu: bound 107c500000.mop (ops vc4_txp_ops [vc4])
[ 3.726913] vc4-drm axi:gpu: bound 107c501000.moplet (ops vc4_txp_ops [vc4])
[ 3.726958] vc4-drm axi:gpu: bound 107c410000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 3.727002] vc4-drm axi:gpu: bound 107c411000.pixelvalve (ops vc4_crtc_ops [vc4])
[ 3.727430] pispbe 1000880000.pisp_be: bcm2712_iommu_of_xlate: MMU 1000005100.iommu
[ 3.727435] pispbe 1000880000.pisp_be: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[ 3.727441] pispbe 1000880000.pisp_be: bcm2712_iommu_device_group: MMU 1000005100.iommu
[ 3.727447] pispbe 1000880000.pisp_be: Adding to iommu group 0
[ 3.727449] pispbe 1000880000.pisp_be: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[ 3.757400] Bluetooth: Core ver 2.22
[ 3.757426] NET: Registered PF_BLUETOOTH protocol family
[ 3.757427] Bluetooth: HCI device and connection manager initialized
[ 3.757433] Bluetooth: HCI socket layer initialized
[ 3.757436] Bluetooth: L2CAP socket layer initialized
[ 3.757441] Bluetooth: SCO socket layer initialized
[ 3.801612] [drm] Initialized vc4 0.0.0 for axi:gpu on minor 1
[ 3.830370] Bluetooth: HCI UART driver ver 2.3
[ 3.830377] Bluetooth: HCI UART protocol H4 registered
[ 3.830396] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 3.830510] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
[ 3.830548] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
[ 3.830576] Bluetooth: HCI UART protocol Broadcom registered
[ 3.833615] rpi-hevc-dec 1000800000.codec: Device registered as /dev/video19
[ 3.902854] Console: switching to colour frame buffer device 320x90
[ 3.921184] vc4-drm axi:gpu: [drm] fb0: vc4drmfb frame buffer device
[ 4.066853] imx708 11-001a: camera module ID 0x0301
[ 4.070297] rp1-cfe 1f00128000.csi: Using sensor imx708 for capture
[ 4.077183] brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
[ 4.077481] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Aug 29 2023 01:47:08 version 7.45.265 (28bca26 CY) FWID 01-b677b91b
[ 4.081004] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-csi2_ch0] node id 0 successfully as /dev/video0
[ 4.082015] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-embedded] node id 1 successfully as /dev/video1
[ 4.082110] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-csi2_ch2] node id 2 successfully as /dev/video2
[ 4.082372] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-csi2_ch3] node id 3 successfully as /dev/video3
[ 4.082429] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_image0] node id 4 successfully as /dev/video4
[ 4.082487] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_image1] node id 5 successfully as /dev/video5
[ 4.082528] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_stats] node id 6 successfully as /dev/video6
[ 4.082557] rp1-cfe 1f00128000.csi: Registered [rp1-cfe-fe_config] node id 7 successfully as /dev/video7
[ 4.190065] Bluetooth: hci0: BCM: chip id 107
[ 4.190266] Bluetooth: hci0: BCM: features 0x2f
[ 4.191310] Bluetooth: hci0: BCM4345C0
[ 4.191313] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0000
[ 4.194346] Bluetooth: hci0: BCM4345C0 'brcm/BCM4345C0.raspberrypi,5-model-b.hcd' Patch
[ 4.560776] Adding 524272k swap on /var/swap. Priority:-2 extents:7 across:2228224k SS
[ 4.625547] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.625553] Bluetooth: BNEP filters: protocol multicast
[ 4.625559] Bluetooth: BNEP socket layer initialized
[ 4.874272] Bluetooth: hci0: BCM: features 0x2f
[ 4.875594] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+-0190
[ 4.875596] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0382
[ 4.875930] Bluetooth: hci0: BCM: Using default device address (m.m.m.m)
[ 4.892502] Bluetooth: MGMT ver 1.23
[ 4.902884] NET: Registered PF_ALG protocol family
[ 5.261143] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL)
[ 5.261154] macb 1f00100000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 5.265156] macb 1f00100000.ethernet: gem-ptp-timer ptp clock registered.
[ 5.297787] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled
[ 7.395211] Bluetooth: RFCOMM TTY layer initialized
[ 7.395236] Bluetooth: RFCOMM socket layer initialized
[ 7.395246] Bluetooth: RFCOMM ver 1.11
[ 2590.430362] usb 1-2: USB disconnect, device number 3
[ 2590.723896] usb 1-2: new full-speed USB device number 4 using xhci-hcd
[ 2590.883495] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 2590.883504] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2590.883507] usb 1-2: Product: Santiago DFU
[ 2590.883510] usb 1-2: Manufacturer: Arduino
[ 2590.883513] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2602.236691] usb 1-2: USB disconnect, device number 4
[ 2602.987917] usb 1-2: new full-speed USB device number 5 using xhci-hcd
[ 2603.148061] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 2603.148068] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2603.148071] usb 1-2: Product: UNO R4 Minima
[ 2603.148074] usb 1-2: Manufacturer: Arduino
[ 2603.148076] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2603.413144] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 2859.015796] usb 1-2: USB disconnect, device number 5
[ 2859.296147] usb 1-2: new full-speed USB device number 6 using xhci-hcd
[ 2859.455935] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 2859.455943] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2859.455945] usb 1-2: Product: Santiago DFU
[ 2859.455947] usb 1-2: Manufacturer: Arduino
[ 2859.455949] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2870.822124] usb 1-2: USB disconnect, device number 6
[ 2871.580138] usb 1-2: new full-speed USB device number 7 using xhci-hcd
[ 2871.740504] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 2871.740511] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2871.740513] usb 1-2: Product: UNO R4 Minima
[ 2871.740515] usb 1-2: Manufacturer: Arduino
[ 2871.740517] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 2871.969569] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 3125.242116] usb 1-2: USB disconnect, device number 7
[ 3125.532098] usb 1-2: new full-speed USB device number 8 using xhci-hcd
[ 3125.691251] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 3125.691259] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3125.691261] usb 1-2: Product: Santiago DFU
[ 3125.691262] usb 1-2: Manufacturer: Arduino
[ 3125.691264] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3137.039498] usb 1-2: USB disconnect, device number 8
[ 3137.792088] usb 1-2: new full-speed USB device number 9 using xhci-hcd
[ 3137.952823] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 3137.952832] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3137.952836] usb 1-2: Product: UNO R4 Minima
[ 3137.952839] usb 1-2: Manufacturer: Arduino
[ 3137.952841] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3138.093904] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 3434.369422] usb 1-2: USB disconnect, device number 9
[ 3434.667838] usb 1-2: new full-speed USB device number 10 using xhci-hcd
[ 3434.827558] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 3434.827563] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3434.827565] usb 1-2: Product: Santiago DFU
[ 3434.827567] usb 1-2: Manufacturer: Arduino
[ 3434.827568] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3446.166744] usb 1-2: USB disconnect, device number 10
[ 3446.919826] usb 1-2: new full-speed USB device number 11 using xhci-hcd
[ 3447.080128] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 3447.080136] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3447.080138] usb 1-2: Product: UNO R4 Minima
[ 3447.080140] usb 1-2: Manufacturer: Arduino
[ 3447.080142] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 3447.228185] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4018.856496] usb 1-2: USB disconnect, device number 11
[ 4019.143065] usb 1-2: new full-speed USB device number 12 using xhci-hcd
[ 4019.302640] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4019.302647] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4019.302650] usb 1-2: Product: Santiago DFU
[ 4019.302651] usb 1-2: Manufacturer: Arduino
[ 4019.302653] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4030.734810] usb 1-2: USB disconnect, device number 12
[ 4031.487044] usb 1-2: new full-speed USB device number 13 using xhci-hcd
[ 4031.647208] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4031.647216] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4031.647218] usb 1-2: Product: UNO R4 Minima
[ 4031.647220] usb 1-2: Manufacturer: Arduino
[ 4031.647221] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4031.831272] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4149.570545] usb 1-2: USB disconnect, device number 13
[ 4149.835082] usb 1-2: new full-speed USB device number 14 using xhci-hcd
[ 4149.994686] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4149.994695] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4149.994699] usb 1-2: Product: Santiago DFU
[ 4149.994702] usb 1-2: Manufacturer: Arduino
[ 4149.994704] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4161.450030] usb 1-2: USB disconnect, device number 14
[ 4162.207177] usb 1-2: new full-speed USB device number 15 using xhci-hcd
[ 4162.368262] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4162.368272] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4162.368275] usb 1-2: Product: UNO R4 Minima
[ 4162.368278] usb 1-2: Manufacturer: Arduino
[ 4162.368281] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4162.525423] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4218.034722] usb 1-2: USB disconnect, device number 15
[ 4218.319564] usb 1-2: new full-speed USB device number 16 using xhci-hcd
[ 4218.478862] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4218.478869] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4218.478871] usb 1-2: Product: Santiago DFU
[ 4218.478873] usb 1-2: Manufacturer: Arduino
[ 4218.478874] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4229.913106] usb 1-2: USB disconnect, device number 16
[ 4230.663646] usb 1-2: new full-speed USB device number 17 using xhci-hcd
[ 4230.824436] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4230.824443] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4230.824446] usb 1-2: Product: UNO R4 Minima
[ 4230.824448] usb 1-2: Manufacturer: Arduino
[ 4230.824449] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4231.008494] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 4650.619805] usb 1-2: USB disconnect, device number 17
[ 4650.977392] usb 1-2: new full-speed USB device number 18 using xhci-hcd
[ 4651.136906] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 4651.136912] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4651.136915] usb 1-2: Product: Santiago DFU
[ 4651.136916] usb 1-2: Manufacturer: Arduino
[ 4651.136918] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4662.507215] usb 1-2: USB disconnect, device number 18
[ 4663.265425] usb 1-2: new full-speed USB device number 19 using xhci-hcd
[ 4663.426474] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 4663.426484] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4663.426488] usb 1-2: Product: UNO R4 Minima
[ 4663.426491] usb 1-2: Manufacturer: Arduino
[ 4663.426494] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 4663.668654] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 5381.196613] usb 1-2: USB disconnect, device number 19
[ 5381.514116] usb 1-2: new full-speed USB device number 20 using xhci-hcd
[ 5381.673756] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[ 5381.673763] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5381.673766] usb 1-2: Product: Santiago DFU
[ 5381.673767] usb 1-2: Manufacturer: Arduino
[ 5381.673769] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 5393.083971] usb 1-2: USB disconnect, device number 20
[ 5393.842119] usb 1-2: new full-speed USB device number 21 using xhci-hcd
[ 5394.002332] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[ 5394.002340] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5394.002342] usb 1-2: Product: UNO R4 Minima
[ 5394.002344] usb 1-2: Manufacturer: Arduino
[ 5394.002346] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[ 5394.198386] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[17534.963569] usb 1-2: USB disconnect, device number 21
[17538.788378] usb 1-2: new full-speed USB device number 22 using xhci-hcd
[17538.948730] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[17538.948737] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[17538.948739] usb 1-2: Product: UNO R4 Minima
[17538.948741] usb 1-2: Manufacturer: Arduino
[17538.948743] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[17539.145796] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[17575.631316] usb 1-2: USB disconnect, device number 22
[17576.000377] usb 1-2: new full-speed USB device number 23 using xhci-hcd
[17576.160462] usb 1-2: New USB device found, idVendor=2341, idProduct=0369, bcdDevice= 1.00
[17576.160469] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[17576.160471] usb 1-2: Product: Santiago DFU
[17576.160473] usb 1-2: Manufacturer: Arduino
[17576.160474] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[17587.518738] usb 1-2: USB disconnect, device number 23
[17588.276367] usb 1-2: new full-speed USB device number 24 using xhci-hcd
[17588.437081] usb 1-2: New USB device found, idVendor=2341, idProduct=0069, bcdDevice= 1.00
[17588.437089] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[17588.437093] usb 1-2: Product: UNO R4 Minima
[17588.437096] usb 1-2: Manufacturer: Arduino
[17588.437098] usb 1-2: SerialNumber: 360A232D36313231202633334B572F27
[17588.684173] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
EEPROM
------
BOOTLOADER: up to date
CURRENT: Thu May 8 02:13:17 PM UTC 2025 (1746713597)
LATEST: Thu May 8 02:13:17 PM UTC 2025 (1746713597)
RELEASE: default (/usr/lib/firmware/raspberrypi/bootloader-2712/default)
Use raspi-config to change the release.
Statistics: Posted by runrook — Sat Jul 26, 2025 10:58 pm